NEFF T T Series, Инструкция по эксплуатации

Страница: 30 / 48

30
Normal noise while the appliance is working
Induction heating technology is based on the creation of
electromagnetic fields that generate heat directly at the base of
the pan. Depending on how the pan has been manufactured,
certain noises or vibrations may be produced such as those
described below:
A deep humming sound as in a transformer
This noise is produced when cooking with a high power level. It
is caused by the amount of energy transferred from the hob to
the pan. The noise disappears or becomes faint when the
power level is lowered.
A low whistling sound
This noise is produced when the pan is empty. The noise
disappears when water or food is added to the pan.
A crackling sound
This noise occurs in pans which are made from different
materials superimposed on one another. It is caused by the
vibrations that occur in the adjoining surfaces of the different
superimposed materials. The noise comes from the pan. The
amount of food and cooking method can vary noise intensity.
A high-pitched whistling sound
This noise is produced mainly in pans made from different
materials superimposed on one another, and it occurs when
such pans are heated at maximum power on two hotplates at
the same time. The whistling disappears or becomes fainter as
soon as the power level is lowered.
Noise from the fan
For proper use of the electronic system, the temperature of the
hob must be controlled. To do this, the hob has a fan which
turns on when a high temperature is detected. The fan may also
work by inertia after the hob has been switched off, if the
temperature detected is still too high.
The noises described are normal, they are part of induction
heating technology and not a sign of malfunction.
After-sales service
Our after-sales service is there for you if your appliance should
need to be repaired. We are committed fo find the best solution
also in order to avoid an unnecessary call-out.
E number and FD number:
Please quote the E number (product number) and the FD
number (production number) of your appliance when
contacting the after-sales service. The rating plate bearing
these numbers can be found on the appliance certificate.
Please note that a visit from an after-sales service engineer is
not free of charge, even during the warranty period.
Please find the contact data of all countries in the enclosed
customer service list.
To book an engineer visit and product advice
Rely on the professionalism of the manufacturer. You can
therefore be sure that the repair is carried out by trained service
technicians who carry original spare parts for your appliances.
Ҥ
+ number /
š + number /
¡
+ number
Electronic system malfunction. Disconnect the range from the mains. Wait about 30 seconds, then
connect it again.*
“§„‰
The Tipp control was dragged instead of
slanting it towards the required hotplate
Wait a few seconds, then switch on the range and hotplate properly
once again.
”‹
/
”Š
There is an internal error in the system. Disconnect the range from the mains. Wait about 30 seconds, then
connect it again.*
”ƒ
The electronic system has overheated and
the related hotplate has been switched off.
Wait for the electronic system to cool down. Then push any symbol
on the range.*
”…
The electronic system has overheated and
all of the hotplates have been turned off.
—‚
Incorrect voltage supply, outside the nor-
mal operating limits.
Please contact your local electricity company.
—ƒ
/
—„
The hotplate has overheated and switched
off to protect its working surface.
Wait until the electronic system has cooled down sufficiently before
switching the hotplate back on.
Indicator Malfunction Measure
* If the indicator persists, call the Technical Assistance Service.
Do not rest hot pans on the control panel.
GB 0844 8928989
Calls from a BT landline will be charged at up to
3 pence per minute. A call set-up fee of up to 6 pence
may apply.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per
minute.