NEFF D96BMV5N5, Инструкция по установке и эксплуатации

Страница: 11 / 25

Imp
ort
Ap
plia
nce
s.c
om
THE EASIEST WAY TO SELF-IMPORT APPLIANCES DIRECT FROM EUROPE.
en
Home Connect
10
o
Home Connect
Home Connect
This appliance can be networked and also controlled
using a mobile device.
If the appliance is not connected to your home network,
it will function as an extractor hood with no network
connection and can still be operated via the display.
The availability of the Home Connect function depends
on the availability of Home Connect services in your
country. Home Connect services are not available in
every country. You can find more information on this at
www.home-connect.com.
Notes
■
Ensure that you follow the safety instructions in this
instruction manual and that you comply with these
even when you are away from home and are
operating the appliance via the Home Connect app.
You must also follow the instructions in the Home
Connect app.
■
Operating the appliance directly from the appliance
always takes priority. It is not possible to operate the
appliance using the Home Connect app during this
time.
Setting up
To implement settings via Home Connect, you must
have installed and set up the Home Connect app on
your mobile device.
Refer to the Home Connect documents supplied for
more information.
The app will guide you through the entire registration
process. Follow the steps specified by the app to
implement the settings.
The app must be open in order to perform the set-up
process.
Notes
■
In networked standby mode, your appliance requires
a maximum of 2 W.
■
If you need your device's MAC address to connect to
your home network, you can find this next to the
rating plate inside the appliance (you will need to
remove the filter to see it).
Automatic registration in the home network
Notes
■
You need a router that has WPS functionality.
■
You need to be able to access your router. If you do
not have this, follow the steps for "Manually logging
into your home network".
■
The extractor hood cannot be switched on during the
connection process. You can cancel the process at
any time by pressing the
#
symbol.
■
To connect the extractor hood to your home
network, the extractor hood must be switched on.
1.
Press and hold the
#
and
˜
symbols at the same
time until the
D
and
Ù
indicators start flashing.
2.
Tap the + symbol to start automatic login to your
home network. D and ‚ will flash.
3.
Press the WPS button on the router within the next
2 minutes.
If the extractor hood has successfully connected, it
will automatically connect to the Home Connect app.
D
and
„
will flash.
Note:
If the extractor hood has been unable to
connect, it will automatically allow you to manually
connect to your home network.
D
and
ƒ
will flash.
Log the appliance into your home network manually
or tap - to try logging in automatically again.
4.
On your mobile device, follow the instructions for
automatic network login.
The login process is complete when the
D
indicator
stops flashing on the control panel and remains
continuously lit.
Manual registration in the home network
Notes
■
The extractor hood cannot be switched on during the
connection process. You can cancel the process at
any time by pressing the
#
symbol.
■
To connect the extractor hood to your home
network, the extractor hood must be switched on.
1.
Press and hold the
#
and
˜
symbols at the same
time until the
D
and
Ù
indicators start flashing.
2.
Tap the + symbol twice to manually log into your
home network.
D
and
ƒ
will flash.
3.
Use the "Home Connect" SSID and the "Home
Connect" key to log your mobile device into the
extractor hood network.
If the extractor hood has successfully connected, it
will automatically connect to the Home Connect app.
D
and
„
will flash.
4.
On your mobile device, follow the instructions for
manually logging into your network.
The login process is complete when the
D
indicator
stops flashing on the control panel and remains
continuously lit.