en
Cleaning function
30
Descaling
The appliance must be descaled regularly in order for it
to continue operating correctly.
There are several steps in the descaling programme.
For hygiene reasons, the descaling programme must
be run through completely so that the appliance can be
ready for operation again.In total, the descaling
programme runs for approx. 70-90 minutes.
■
Descale (approx. 55-70 minutes), then empty and
refill the water tank
■
First rinsing cycle (approx. 6-9 minutes), then empty
and refill the water tank
■
Second rinsing cycle (approx. 6-9 minutes), then
empty and dry the water tank
If the descaling process is interrupted (for example, due
to a power failure or because the appliance has been
switched off), you are prompted to rinse the appliance
twice after it is switched back on. The appliance cannot
be used until the second rinsing cycle has come to an
end.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible, or fewer, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Starting
Caution!
Damage to the appliance: Only use liquid descalers
recommended by us for the descaling programme.
Other descalers may damage the appliance.
Descaler order no.: 311 680
Caution!
Descaling solution: Do not allow descaling solution to
come into contact with the control panel or other
sensitive surfaces. This will damage the surfaces. If this
does happen, remove the descaling solution
immediately with water.
The descaling programme can only be started once the
cooking compartment has completely cooled down. If
the temperature in the cooking compartment is too
high, a message appears on the display. Wait until the
cooking compartment has cooled down. Then restart
the process.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
1.
Mix 500 ml water with 150 ml liquid descaler to
make a descaling solution.
2.
Touch the
#
touch button.
3.
Remove the water tank and fill with descaling
solution.
4.
Fully insert the water tank filled with the descaling
solution.
5.
Close the control panel.
6.
Touch the
0
touch button.
7.
Swipe to the left or right to select "Descale
,
".
8.
Touch the bottom line.
The duration of the descaling programme is
displayed. It cannot be changed.
9.
Touch the bottom line.
10.
Touch the
#
touch button.
The appliance is descaled. The remaining time
counts down on the display. As soon as the
descaling programme has finished, an audible
signal sounds.
First wash cycle
1.
Open the control panel.
2.
Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3.
Close the control panel.
4.
Touch the
#
touch button.
The appliance is rinsed. As soon as the wash cycle
has finished, an audible signal sounds.
Second wash cycle
1.
Open the control panel.
2.
Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3.
Close the control panel.
4.
Touch the
#
touch button.
The appliance is rinsed. As soon as the wash cycle
has finished, an audible signal sounds.
Final cleaning
1.
Open the control panel.
2.
Empty and dry the water tank.
3.
Switch off the appliance.
Descaling is complete and the appliance is ready for
use again.
Содержание C18FT56.0B
Страница 1: ...en INSTRUCTION MANUAL Combination steam oven C18FT56 0B...
Страница 2: ......
Страница 58: ......
Страница 59: ......