NEFF B46C42 0 Series, Инструкция по эксплуатации

Страница: 9 / 40

9
8.
Use the temperature selector to set the temperature to
240 °C.
9.
Press the Ÿ VarioSteam button repeatedly until "High steam
intensity" appears in the text display (see section:
VarioSteam - steam-assisted cooking).
10.
Press the ƒ Start button.
11.
Switch off the appliance if the water tank is empty. To do
this, turn the operating mode selector to the Û off position
and push it in.
The remaining water will be pumped out of the evaporator
system.
12.
Emptying the water tank (see section: Filling and emptying
the water tank)
13.
Afterwards, wipe the cooled cooking compartment with hot,
soapy water.
Note:
Remove limescale marks with a cloth soaked in
vinegar, then wipe over with clean water and rub dry with a
soft cloth.
14.
Clean the outside of the appliance with a soft, damp cloth
and soapy water.
Operating the appliance
In this section, you can read about
■
how to switch your appliance on and off
■
how to select an operating mode and temperature
■
how to fill and empty the water tank
■
when your appliance switches off automatically
Switching on the appliance
Press the operating mode selector to make it pop out.
This switches on the appliance, and it is now ready for use.
"Appliance is ready for use" and "Oven light" appear in the text
display.
Selects the operating mode and temperature
ã=
Risk of scalding!
The water in the water tank may become very hot if you
continue to operate the appliance. Empty the water tank after
each steam-assisted application.
Notes
■
The / Low-temperature cooking, é Steam cooking, ê
Dough proving and > EasyClean® operating modes can
only be started once the appliance has cooled down. There
must be no residual heat shown in the temperature display
(neither • nor œ ).
■
For cooking with steam, you must fill the water tank (see
section: Filling and emptying the water tank).
1.
Switch on the appliance.
2.
Turn the operating mode selector until the desired operating
mode appears on the text display.
3.
Turn the temperature selector to change the default
temperature.
Note: If no default temperature is displayed, the temperature
of your selected operating mode is set permanently. You
cannot change this temperature.
4.
Press the ƒ Start button.
Notes
■
Depending on the operating mode that you have selected,
you will hear a pumping noise after the operation has started.
The appliance is checking whether the pumps are working
correctly.
■
If you cannot start a steam-assisted application, check
whether the water tank has been filled and fully inserted.
Changing the operating mode
1.
Turn the operating mode selector until the desired operating
mode is selected.
2.
Turn the temperature selector to change the temperature.
3.
Press the ƒ Start button.
Current temperature
Press the
±
info button. The current temperature appears for
3 seconds.
Note:
The current temperature can only be displayed with
operating modes with a default temperature.
&LUFR7KHUP
Operating mode Default temper-
ature in °C
Temperature
range in °C
3 CircoTherm®*
160 40 - 200
A
Defrost
Fixed setting
A A A
%
Top/bottom heat*
170 50 - 275
0 Circotherm intensive*
220 50 - 275
ë Bread-baking*
200 180 - 220
$
Bottom heat
200 50 - 225
4
Circo-roasting*
170 50 - 250
+ Full-surface grill
+
Full-surface grill (inten-
sive)**
220 50 - 275
Fixed setting
(
Centre-area grill
( Centre-area grill (inten-
sive)**
180 50 - 275
Fixed setting
/
Low-temperature cooking Fixed setting
ü ü ü
é
Steam cooking Fixed setting
¨©¨
ê Dough proving
Fixed setting
A ƒ A
> EasyClean®
Fixed setting
“’†
ä
Reheat
120 80 - 180
* You can activate steam for this operating mode
** Turn the temperature selector beyond 275 °C.
‚Ÿ£
appears
in the temperature display