NEFF B46C42 0 Series, Инструкция по эксплуатации

Страница: 8 / 40

8
Setting the language
"Select language English" is preset. If necessary, set another
language for the text display.
1.
Turn the temperature selector until the language you require
appears on the text display.
2.
Press and hold the ± info button for 3 seconds.
Your setting is saved. "Water hardness 3 - hard" appears in
the text display.
Setting the water hardness
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
"Water hardness 3 - hard" is preset. Change this setting if your
water is softer.
You can use the test strip supplied to determine the water
hardness, or you can ask your water supplier.
Notes
■
If your water is very hard, we recommend that you use
softened water.
■
If you use only softened water, you can set your appliance to
"Water hardness (softened)".
■
If you use mineral water, set the hardness to "Water hardness
3 - hard".
■
If you use mineral water, you must only use non-carbonated
mineral water (see section "Filling and emptying the water
tank").
1.
Use the temperature selector to set the water hardness.
2.
Press and hold the ± info button for 3 seconds.
Your setting is saved. "Altitude calibration 0 - 300 m" is
shown in the text display.
Altitude calibration
The altitude range is preset to "0 - 300m". Change this setting if
the location of your appliance is at a higher or lower altitude.
1.
Use the temperature selector to set the altitude range.
2.
Press and hold the ± info button for 3 seconds.
Your setting is saved.
Setting the clock
Note:
When you press the
KJ
clock function button, you have
3 seconds to set the clock using the rotary selector. Should this
have been insufficient for you, you can amend the clock time
later.
‹ : ‹‹ flashes in the clock display.
1.
Briefly press the
KJ
clock function button to go to the
setting mode.
The
KJ
and
3
symbols light up.
‚ƒ
:
‹‹
appears in the
clock display.
2.
Set the current time using the rotary selector.
Your setting is accepted after 3 seconds.
Changing the clock
To subsequently change the time, press the KJ clock function
button repeatedly until the
KJ
and
3
symbols light up again.
Change the time with the rotary selector.
Cleaning the appliance
Clean your appliance before using it for the first time.
1.
Remove the accessories from the cooking compartment.
2.
Completely remove any residual packaging (e.g. chips of
polystyrene) from the cooking compartment.
3.
Clean the accessories and cooking compartment with hot
soapy water (see section: Cleaning and care).
4.
Fill the water tank with 400 ml water (see section: Filling and
emptying the water tank).
5.
Slide in the water tank all the way.
6.
Switch on the appliance. To do this, press the operating
mode selector so that it pops out (see section: Operating the
appliance).
The appliance is then ready for use.
7.
Use the operating mode selector to set
%
Top/bottom heat.
Water hardness Setting symbol (temperature
display)
softened
™†‹
1 ­ soft
™†‚
2 ­ medium
™†ƒ
3 ­ hard
™†„
6HOHFWODQJXDJH
(QJOLVK
Altitude range Setting symbol (temperature
display)
below 0 m
™‡‹
0 - 300m
™‡‚
300 - 600m
™‡ƒ
600 - 900m
™‡„
900 - 1200m
™‡…
1200 - 1500m
™‡†
1500 - 1800m
™‡‡
1800 - 2100m
™‡ˆ
2100 - 2400m
™‡‰
above 2400m
™‡Š