NEFF B46C42 0 Series, Инструкция по эксплуатации

Страница: 10 / 40

10
Heating indicator
The heating indicator displays the rising temperature in the
cooking compartment.
■
Temperature reached (figure A)
■
Appliance reheating (figure B)
Filling and emptying the water tank
ã=
Risk of injury and risk of fire!
Only fill the water tank with water or with the descaling solution
that is recommended by us.
Do not pour any flammable liquids (e.g. alcoholic drinks) into
the water tank.
Due to hot surfaces, vapours from flammable liquids may catch
fire in the cooking compartment (explosion). The appliance
door may spring open. Hot steam and jets of flame may
escape.
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
Notes
■
If you use mineral water, set the water hardness to hard.
■
For hygiene reasons, a reminder message will appear after
the appliance is switched off if the water tank has not been
emptied. The reminder message goes out once the water
tank is empty.
Filling the water tank
Fill the water tank before each use with steam assistance.
1.
Press lightly on the centre of the lower edge of the water tank
(picture A).
2.
Pull out the water tank (picture B).
3.
Fill the water tank with cold water up to the "max" mark
(picture C).
4.
Slide in the water tank all the way.
Refilling the water tank
If the water tank is empty, a signal sounds. "Fill water tank and
slide in fully" appears in the display. Steam-assisted operation
is interrupted.
1.
Pull out the water tank.
2.
Fill the water tank up to the "max" mark and slide it in fully.
The steam-assisted operation continues.
Emptying the water tank
Empty the water tank after each steam-assisted use of the
appliance.
1.
Turn the operating mode selector back to the Û off position
and push it in.
"Pumping-out" appears in the text display and
˜ž© (pumping
out) appears in the temperature display. The remaining water
in the evaporator system is pumped back into the water tank.
After the pumping, "Pumping-out finished" appears.
2.
Pull out the water tank slowly and level.
3.
Remove the cover (Picture A).
4.
Empty the water tank (Picture B).
5.
Thoroughly dry the water tank recess and the water tank.
6.
Slide in the water tank.
Switching off the appliance
ã=
Risk of scalding!
When you open the appliance door, hot steam can escape.
Open the appliance door carefully after cooking.
Note:
The appliance has a cooling fan. After the appliance is
switched off, the cooling fan may continue to run.
1.
Turn the operating mode selector back to the
Û
off position
2.
Press the operating mode selector in so that it stays in.
The appliance switches off.
Note:
If the appliance is switched off after a steam-assisted
operation, you will hear a pumping sound. The appliance is
pumping the remaining water out of the evaporator system
back into the water tank. "Pumping-out" appears in the text
display. Only empty the water tank once "Pumping-out finished"
is displayed.
You can see in the temperature display whether there is high or
low residual heat in the cooking compartment.
Turning off the operation
Press and hold the „ Stop button. The appliance turns off the
current operation. The appliance is not switched off. You can
now start a different operating mode.
Interrupting and continuing an operation (Pause)
Briefly press the „ Stop button. The appliance interrupts the
current operation. Press the ƒ Start button to continue the
paused operation.
$ %
$ %
&
Temperature
display
Text display Meaning
•
Residual heat
high
Residual heat high
(above 120 °C)
œ
Residual heat
low
Residual heat low
(between 60 °C and 120 °C)
$ %