9
Changing the operating mode
1.
Turn the operating mode selector until the desired operating
mode is selected.
2.
Turn the temperature selector to change the temperature.
3.
Press the
ƒ
Start button.
Current temperature
Press the
±
info button. The current temperature appears for
3 seconds.
Note:
The current temperature can only be displayed with
operating modes with a default temperature.
Heating indicator
The heating indicator displays the rising temperature in the
cooking compartment.
■
Temperature reached (figure A)
■
Appliance reheating (figure B)
Filling and emptying the water tank
ã=
Risk of injury and risk of fire!
Only fill the water tank with water or with the descaling solution
that is recommended by us.
Do not pour any flammable liquids (e.g. alcoholic drinks) into
the water tank.
Due to hot surfaces, vapours from flammable liquids may catch
fire in the cooking compartment (explosion). The appliance
door may spring open. Hot steam and jets of flame may
escape.
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
Note:
If you use mineral water, set the hardness to "Water
hardness - hard".
Filling the water tank
Fill the water tank before each use with steam assistance.
1.
Press lightly on the centre of the lower edge of the water tank
(picture A).
2.
Pull out the water tank (picture B).
3.
Fill the water tank with cold water up to the "max" mark
(picture C).
4.
Slide in the water tank all the way.
Note:
If the
Î
symbol flashes, the water tank has not been
pushed in fully.
Topping up the water tank
If the water tank is empty, a signal sounds and the
Î
symbol
lights up. Steam-assisted operation is interrupted.
1.
Pull out the water tank.
2.
Fill the water tank up to the "max" mark and slide it in fully.
The steam-assisted operation continues.
Emptying the water tank
Empty the water tank after each steam-assisted use of the
appliance.
1.
Turn the operating mode selector back to the
Û
off position
and push it in.
The remaining water in the evaporator system is pumped
back into the water tank. The
Ì
symbol lights up.
˜ž©
appears in the temperature display. (pumping-out). When the
pumping out cycle is complete, a signal sounds and the
Î
symbol flashes.
2.
Pull out the water tank slowly and level.
The
Î
symbol goes out.
3.
Remove the cover (Picture A).
4.
Empty the water tank (Picture B).
5.
Dry the tank shaft and water tank thoroughly.
6.
Slide in the water tank.
The
Î
symbol and the
˜ž©
display (pumping-out) go out.
0
Circotherm intensive*
220
50 - 275
4
Circo-roasting*
170
50 - 250
+
Full-surface grill
+
Full-surface grill (inten-
sive)**
220
50 - 275
Fixed setting
(
Centre-area grill
(
Centre-area grill (inten-
sive)**
180
50 - 275
Fixed setting
$
Bottom heat
200
50 - 225
/
Low-temperature cooking Fixed setting
ü
ü
ü
A
Defrost
Fixed setting
A A A
>
EasyClean®
Fixed setting
“’†
ä
Reheat
120
80 - 180
Operating mode
Default temper-
ature in °C
Temperature
range in °C
* You can activate steam for this operating mode
** Turn the temperature selector beyond 275 °C.
‚Ÿ£
appears
in the temperature display
$
%
$
%
&
$
%
Содержание B45C42.0
Страница 1: ... en Instruction manual Built in oven B45C42 0 ...
Страница 34: ...34 ...
Страница 35: ...35 ...
Страница 36: ...910302 9000456399 9000456399 Constructa Neff Vertriebs GmbH Carl Wery Straße 34 D 81739 München ...