NEFF B45C42.0, Инструкция по эксплуатации

Страница: 7 / 36

7
Note:
The baking tray and universal pan may become distorted
during use. This is caused by the considerable temperature
differences acting on the accessories. This may happen when
only a part of the accessory is covered with food or when
frozen items such as pizza have been placed on the accessory.
Before using the appliance for the first time
Once your new appliance has been connected, ™…„ appears
in the temperature display. Before you can use your appliance,
you must make a few settings:
■
Set the water hardness range
■
Calibrate the altitude
■
Set the clock
■
Clean the appliance before using it for the first time
Note: You can correct these settings at any time. For
information about changing the water hardness range and the
altitude difference, see chapter: Changing the basic settings;
and for information about setting the clock, see chapter:
Electronic clock.
Setting the water hardness range
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
The water hardness “hard“ ( ™…„ ) is the default setting. Change
the setting if the water is softer.
You can determine the water hardness with the test strips
supplied or ask your water supplier.
Notes
■
If your water is very hard, we recommend that you use
softened water.
■
If you use only softened water, you can, in this case, set your
appliance to the softened water hardness range.
■
If you use mineral water, then set the water hardness range to
hard.
■
If you use mineral water, then it must be non-carbonated (see
chapter: Filling and emptying the water tank).
1.
Use the temperature selector to set the water hardness
range.
2.
Press and hold the ± info button for 3 seconds.
Your setting is saved. ™†‚ appears in the temperature
display.
Calibrating the altitude
The altitude difference range “0 - 300m“ (
™†‚
) is the default
setting. Change this setting if the location of the appliance is
higher or lower than this.
1.
Use the temperature selector to set the altitude difference
range.
2.
Press and hold the ± info button for 3 seconds.
Your setting is saved.
Setting the clock
Note:
When you press the KJ clock function button, you have
3 seconds to set the clock using the rotary selector. Should this
have been insufficient for you, you can amend the clock time
later.
‹ : ‹‹ flashes in the clock display.
1.
Briefly press the KJ clock function button to go to the
setting mode.
The
KJ and 3 symbols light up. ‚ƒ : ‹‹ appears in the
clock display.
2.
Set the current time using the rotary selector.
Your setting is accepted after 3 seconds.
Universal pan, non-stick Z1233X0
Universal pan with wire insert Z1242X0
Glass pan Z1262X0
Roasting pan, enamelled Z1272X0
Baking tray, aluminium Z1332X0
Baking tray, enamelled Z1342X0
Baking tray, non-stick Z1343X0
Pizza tray Z1352X0
Wire rack, stepped with cut-out Z1432X0
Wire rack, flat Z1442X0
Accessories Order no.
Roasting tray, enamelled, two-piece Z1512X0
CLOU 3x telescopic railings retrofit kit Z1742X1
CLOU 4x telescopic railings retrofit kit Z1752X1
Bread-baking stone Z1912X0
Universal roasting dish, enamelled Z9930X0
Accessories Order no.
Water hardness range Setting symbol (temperature dis-
play)
softened
™…‹
soft
™…‚
medium
™…ƒ
hard
™…„
Altitude difference
range
Setting symbol (temperature dis-
play)
Under 0m
™†‹
0 - 300m
™†‚
300 - 600m
™†ƒ
600 - 900m
™†„
900 - 1200m
™†…
1200 - 1500m
™††
1500 - 1800m
™†‡
1800 - 2100m
™†ˆ
2100 - 2400m
™†‰
above 2400m
™†Š