Necta Vending Solutions SpA StarFood Скачать руководство пользователя

Страница: 49 / 68

0401 171-02

Programming button

Technician menu - Summary

TECH >2.4.5

Display Euro

TECH >2.4.5

Display

Enabled/disabled

Enabled

Disabled

TECH >2.4.6

Dis. count at start-up

Status

Enabled/disabled

TECH >2.4.6

Display counter

at start-up

Enabled

Disabled

TECH >2.5

Miscellaneous

TECH >2.5.1

Password

TECH >2.5.1.2

Status

Five-digit number to access

programming.

If set to Zero (default) the

password is not required.

TECH >2.5.1.1

Password

TECH >2.5.1.2

Password

TECH >2.5.1.1

Enter password

Password = ###

Enabled/disabled

When confirming the blinking

values, hour and minute for

start and end of time band

are entered one after the

other.

When start and end of time

band are set to 00.00 the

bands are not activated.

TECH >2.5.2.2

Time band 1÷ 2

TECH >2.5.2.2

Time band 1

Start band ##

End band ## ##

TECH >2.5.2.2

Day 1÷ 7

TECH >2.5.2

Energy saving

TECH >2.5.2.1

Energy saving

Enabled/disabled

TECH >2.5.2.1

Switch off lamps

Enabled/disabled

Содержание StarFood





































































Результаты поиска

Содержание StarFood

Отзывы:

Похожие инструкции для StarFood

Бренды по названию

Популярные бренды

Necta Vending Solutions SpA StarFood, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание StarFood

Отзывы:

Похожие инструкции для StarFood

Бренды по названию

Популярные бренды