NEC UNIVERGE NEAX 2000 IPS Скачать руководство пользователя страница 22

Страница: 22 / 96

NEAX 2000 IPS Configuration Guide

Page 12

NDA-24347, Issue 1

System Outline

Chapter 2 System Configuration

System Outline

The NEAX 2000 IPS is an IP communication system that integrates the voice
terminals to the IP network through Peer-to-Peer connection.

The system is a hybrid system to accommodate both IP multi-line terminals (Dterm
IP) and the terminals used in Legacy PBXs (Legacy terminal).

Line/Trunk cards and Application Processor cards can be mounted in the system to
provide the features that are provided by Legacy Time Division Switch (TDSW)
PBXs.

Figure 2-5 System Outline of NEAX 2000 IPS

PBX

TDSW

C.O.

IP-PAD

TIE

IPT (H.323
Handler)

NEAX 2000 IPS

SLT/Dterm

LC/DLC

DRS-Network Based (as Proxy)

Client PC

Dterm IP

Router

MAT (via LAN)

Router

H.323 GK

LAN

PSTN/

GSTN

Switching HUB

Dterm IP

Client PC

Switching HUB (100 Mbps)

INTERNET/

INTRANET

Dterm IP

1board MP

Содержание UNIVERGE NEAX 2000 IPS

































































































Результаты поиска

Содержание UNIVERGE NEAX 2000 IPS

Отзывы:

NEC UNIVERGE NEAX 2000 IPS, Руководство по настройке, Страница: 22 / 96

Результаты поиска

Содержание UNIVERGE NEAX 2000 IPS

Отзывы: