NEC SV8500 Скачать руководство пользователя страница 363

Страница: 363 / 410

– 347 –

ACDIZ : Internal ACDP Initialization Control

ACDIZ: Internal ACDP Initialization Control

Function

This command is used to initialize Internal ACDP on a standalone basis.

Precautions

(1) When executing the ACDP initialization, the agents currently logged onto the ACD system are forced

to log-off state. To restart the agent operation, the agents must log on to the system again.

(2) When restarting the ACDP after this ACDP initialization, the system message "6-H" will issued.

(3) If this ACDP initialization is performed while the ACDP accesses the MIS application, the status of

the MIS application will not be displayed properly. In that case, restart the MIS system after the com-

pletion of the ACDP initialization.

(4) To perform this initialization, the following data settings are required.

ASYD, SYS1, INDEX2, b0-b3 = 01 Hex (ACDP is mounted)

ASYD, SYS1, INDEX207 = 03 Hex (ACDP Mounting Information)

ASYDL, SYS1, INDEX864, b0 = 1 (Built-in IP, ACDP is used)

Parameters

ACDP:

Fixed to 0 (Not used)

KIND:

Select either of radio buttons: Initial/Make busy

Program Load:

Click the check box to ON when executing Program Load.

Office Data:

Select either of radio buttons: Retain/Clear/Load

Retain: Internal ACDP is initialized while maintaining the existing ACDP office data.

Clear: Internal ACDP is initialized and the existing ACDP office data except the office

data files in Flash Card Memory is all cleared. To clear the office data files in Flash

Card Memory, write the cleared ACDP office data into Flash Card Memory by using

MEM_HDD after the execution of this command.

Load: Internal ACDP office data is loaded from Flash Card Memory, and then Internal

ACDP is initialized.

[Drive Selection] (This field becomes effective by selecting "Load" on the above "Office Data" parameter.)

Program:

(For the system using the Redundant Data Memory Backup function:)

Specify the destination drive for the ACDP Program loading.

- Drive A (Default Setting)

- Drive D

(For the system not using the Redundant Data Memory Backup function:)

Drive A (Default Setting) must be selected.

Office Data:

(For the system not using the Redundant Data Memory Backup function:)

Specify the destination drive for the ACDP Office Data loading.

- Drive B (Default Setting)

- Drive C

(For the system not using the Redundant Data Memory Backup function:)

Drive B (Default Setting) must be selected.

Current ACDP Status:The current ACDP status is displayed.

Current Sequence Counter: The current Sequence Counter is displayed.

Содержание SV8500



























































































































































































































































































































































































































Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды

NEC SV8500, Руководство по программированию

Результаты поиска

Содержание SV8500

Отзывы:

Похожие инструкции для SV8500

Бренды по названию

Популярные бренды