NEC SV8500 Скачать руководство пользователя страница 335 | Manualshive

Страница: 335 / 410

background image

– 319 –

ACDPLT : Assignment of ACD Monitor Number

ACDPLT: Assignment of ACD Monitor Number

1.

Function

This command is used to assign, display, print, and remove ACD pilot data. This consists of a pilot number
that designates the pilot to which ACD calls are routed and the Call Control Vector call processing path to
be taken. Internal and Transfer Priorities can be designated as well as an optional pilot name.

2.

Precautions

(1) A Call Control Vector is a list of instructions describing the procedure to be used in handling an indi-

vidual call. Call processing steps are determined by the pilot number. Pilot numbers associate the call
processing procedure with a Call Control Vector. Additional information about CCV programming
can be found under ACDCCV.

(2) Pilot numbers should be assigned as monitor numbers (see AMNO or AMNON in this chapter).
(3) Different pilot numbers can route to the same CCV or Week Schedule and use different priorities.
(4) If an invalid pilot number is assigned, it may cause the Call Recover feature not to work.
(5) For a maximum number of pilots in a ACD system, see Section 2. 3. 1 “ACD System Capacity” in

CHAPTER 2.

(6) One-digit pilot number may not be assigned.

Note 1:

Pilot Number is the same number programmed in AMNO or AMNON.

Note 2:

Personal Pilot Numbers are not programmed in ADCPLT.

3.

Parameters

TN:

Tenant Number (1 to 9)

M_NO:

The number used for the pilot in ACD call routing (Two to five digits. Unify the number
of digits.)

Note:

Use numbers 0-9. *,# may not be used. 1stDC="0" may not be used.

ACDP:

Fixed to 0 (Not used)

NAME:

Pilot Name, up to 20 characters.

TRKPRI:

Priority at which ACD trunk calls are queued (1 to 250).

INPRI:

Priority with which internal calls are queued (1 to 250).

TRPRI:

Priority at which transferred calls are queued (1 to 250).

CCV/W:

0/1=CCV/Week Schedule

CCVNO:

CCV index number (1-900)

CCVSTP:

CCV step number (1-20)

N_CCVNO:

Night CCV Index (1 to 900)
0 : feature not used

N_CCVSTP:

Night CCV step number (1-20)

WEEKNO:

Week Schedule number (1-250)

«
...
333
334
335
336
337
...
»

Содержание SV8500



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SV8500

Бренд: Korenix Страницы: 2

Бренд: Galleon Страницы: 35

Бренд: Supero Страницы: 112

AirborneDirect ABDG-SE-IN5410

Бренд: Quatech Страницы: 8

digitalSTROM-Server

Бренд: aizo Страницы: 2

BladeCenter JS20

Бренд: IBM Страницы: 132

Бренд: Inspur Страницы: 82

Бренд: TYANO Страницы: 102

PRIMERGY RX300 S6

Бренд: Fujitsu Страницы: 132

PRIMERGY RX300 S5

Бренд: Fujitsu Страницы: 112

PRIMERGY RX2540 M4

Бренд: Fujitsu Страницы: 86

PRIMERGY RX2540 M6

Бренд: Fujitsu Страницы: 121

PRIMERGY RX4770 M6

Бренд: Fujitsu Страницы: 468

PRIMERGY RX2540 M1

Бренд: Fujitsu Страницы: 92

PRIMERGY RX2540 M5

Бренд: Fujitsu Страницы: 112

PRIMERGY RX2540 M4

Бренд: Fujitsu Страницы: 639

PRIMERGY RX2540 M2

Бренд: Fujitsu Страницы: 602

PRIMERGY RX2530 M5

Бренд: Fujitsu Страницы: 486

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды