manualshive.com logo in svg

NEC SOPHO IP 5000, Справочник по командам, Страница: 126 / 191

Поделиться
Скачать
NEC SOPHO IP 5000 Скачать руководство пользователя страница 126

 

 

SOPHO 

IP 5000/SOPHO IP6000 

 

Command Reference Guide 

 

126

 

 
<NEC-PHILIPS> 

display interface ethernet 2/0/0 

Ethernet2/0/0 current state : UP 
Line protocol current state : UP 
Description : NEC-PHILIPS Routers, Ethernet0/0 Interface 
The Maximum Transmit Unit is 1500, Hold timer is 10(sec) 
Internet Address is 172.31.29.103/16 
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 
00e0.fc06.3085 
Media type is twisted pair, loopback not set, promiscuous mode not set 
100Mb/s-speed mode,Full-duplex mode,link type is autonegotiation 
Output flow-control is unsupported, input flow-control is unsupported 
Output queue : (Urgent queue : Size/Length/Discards) 0/500/0 
Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0 

Last 5 minutes input rate 227.13 bytes/sec, 2.67 packets/sec 
Last 5 minutes output rate 0.00 bytes/sec, 0.00 packets/sec 
Input: 542665 packets, 47721004 bytes 

271460 broadcasts, 271205 multicasts 
0 errors, 0 runts, 0 giants, 
0 CRC, 0 align errors, 0 overruns, 
0 dribbles, 0 aborts, 0 no buffers 

Output:0 packets, 0 bytes 

0 errors, 0 underruns, 0 collisions 
0 deferred 

 
 

duplex  

Syntax  
duplex { full | half | negotiation }  
undo duplex  
 
View  

Ethernet interface view  
 

Parameter  
full

: Sets the Ethernet interface to work in full duplex mode.  

 

half

: Sets the Ethernet interface to work in half duplex mode.  

 

negotiation

: Sets the Ethernet interface to work in auto-negotiation mode.  

 
Description  

Using the 

duplex

 command, you can set the operating mode of the 100Base-

TX  FE interface. Using the 

undo duplex

 command, you can restore the default  

operating mode of the Ethernet interface.  
 
By default, the Ethernet interface is working in auto-negotiation mode.  
 
An Ethernet interface on a router that is connected to a hub must work in  half-
duplex mode. When an Ethernet interface is connected to a network device  
that supports full-duplex, it must work in full-duplex mode, however.  
 
Before setting the FE interface to work in auto-negotiation mode, you must 
make  sure that the connected remote end has been working in auto-negotiation 
mode.  If this cannot be guaranteed, the two parties should use the forced 
setting for the  consistency in operating mode.  
 
For related commands, see 

speed and display interface

.  

 

Example  

Set the 100Base-TX FE interface to work in full duplex mode.  
 
[NEC-PHILIPS-Ethernet0/0/0] 

duplex full  

Содержание SOPHO IP 5000
































































































































































































Отзывы:

Нет отзывов