manualshive.com logo in svg

NEC mPD703128, Предварительное руководство пользователя

"NEC mPD703128" - это микросхема высокой производительности, для которой доступно предварительное Руководство пользователя. Скачайте его бесплатно на manualshive.com. Получите подробные инструкции по использованию этого продукта, чтобы максимально эффективно использовать все его возможности.

Поделиться
Скачать
background image

376

Chapter 13

Serial Interface Function

Preliminary User’s Manual U15839EE1V0UM00

(2)

Transmit operation

When Power bit is set to 1 in the ASIMn register, a high level is output from the TXD5n pin.
Then, when TXE bit is set to 1 in the ASIMn register, transmission is enabled, and the transmit
operation is started by writing transmit data to transmission buffer register (TXBn) (n = 0, 1).

(a)  Transmission enabled state
This state is set by the TXE bit in the ASIMn register.

• TXE = 1: Transmission enabled state

• TXE = 0: Transmission disabled state

Since UART5n does not have a CTS (transmission enabled signal) input pin, a port should be
used to confirm whether the destination is in a reception enabled state.

(b)  Starting a transmit operation
In transmission enabled state, a transmit operation is started by writing transmit data to 
transmission buffer register (TXBn). When a transmit operation is started, the data in TXBn is
transferred to transmission shift register. Then, the transmission shift register outputs data to the
TXD5n pin (the transmit data is transferred sequential starting with the start bit). The start bit, 
parity bit, and stop bits are added automatically.

(c)  Transmission interrupt request
When the transmission shift register becomes empty, a transmission completion interrupt request
(INTSTn) is generated. The timing for generating the INTSTn interrupt differs according to the
specification of the number of stop bits. The INTSTn interrupt is generated at the same time that
the last stop bit is output.
If the data to be transmitted next has not been written to the TXBn register, the transmit operation
is suspended.

Caution:

Normally, when the transmission shift register becomes empty, a transmission 
completion interrupt (INTSTn) is generated. However, no transmission completion
interrupt (INTSTn) is generated if the transmission shift register becomes empty due
to the input of a RESET.

Figure 13-8:

Asynchronous Serial Interface Transmission Completion Interrupt Timing

Start

Stop

D0

D1

D2

D6

D7

Parity

Parity

TXDn (output)

INTSTn (output)

Start

D0

D1

D2

D6

D7

TXDn (output)

INTSTn (output)

(a)  Stop bit length: 1

(b)  Stop bit length: 2

Stop

Содержание mPD703128





































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для mPD703128

IBM ServeRAID M5014 User Manual preview
ServeRAID M5014
Бренд: IBM Страницы: 106
Garmin TR-1 Gold Installation Instructions preview
TR-1 Gold
Бренд: Garmin Страницы: 4
LANGER EMV-Technik E 1 User Manual preview
E 1
Бренд: LANGER EMV-Technik Страницы: 48
National Instruments sbRIO-9629 Quick Reference Manual preview
sbRIO-9629
Бренд: National Instruments Страницы: 2
Apricus Sentinel S4 Mounting, Connection, Operation preview
Sentinel S4
Бренд: Apricus Страницы: 32
Analog Devices Linear Technology ADI Power DC3017A Demo Manual preview
Linear Technology ADI Power DC3017A
Бренд: Analog Devices Страницы: 12
Delta DZNT-104T Installation Manual preview
DZNT-104T
Бренд: Delta Страницы: 16
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Бренд: H.E. Anderson Страницы: 11
Nabtesco CONPAL NCB-8C-SR User Manual preview
CONPAL NCB-8C-SR
Бренд: Nabtesco Страницы: 24
Topcon OPUS A3 Eco Get Started preview
OPUS A3 Eco
Бренд: Topcon Страницы: 9
SUPMEA SUP-DC2000 User Manual preview
SUP-DC2000
Бренд: SUPMEA Страницы: 40
Hanbay RD-AC Series User Manual preview
RD-AC Series
Бренд: Hanbay Страницы: 13
Gigarise SetPro MV Series Instruction Manual preview
SetPro MV Series
Бренд: Gigarise Страницы: 18
Danaher Motion S20630 Installation Manual preview
S20630
Бренд: Danaher Motion Страницы: 109
Fuji Electric FRENIC-EcoPAK Instruction Manual preview
FRENIC-EcoPAK
Бренд: Fuji Electric Страницы: 22
AMX NX-2200 Quick Start Manual preview
NX-2200
Бренд: AMX Страницы: 2
cnsat Smart Antenna Selector Instruction Manual preview
Smart Antenna Selector
Бренд: cnsat Страницы: 14
Parker COMPAX 02 Series User Manual preview
COMPAX 02 Series
Бренд: Parker Страницы: 242

Бренды по названию

Популярные бренды

Загрузить еще бренды