51
7. Appendix
Common Problems & Solutions
(
→
"Power/Status/Lamp Indicator" on page
50
.)
Does not turn on
Will turn off
No picture
Picture suddenly
becomes dark
Color tone or hue is
unusual
Image isn’t square to
the screen
Picture is blurred
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or
blinking
Cross color in RGB
mode
• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. (
→
page
16
,
17
)
• Ensure that the lamp cover is installed correctly. (
→
page
48
)
• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the
room where you are presenting is particularly warm, move the projector to a cooler location.
• Check to see if the lamp usage exceeds 2100 hours (up to 2600 hours : Eco mode). If so, replace the lamp.
After replacing the lamp, reset the lamp hours used.(
→
page
45
)
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• Ensure that the Power Management or Off Timer is off. (
→
page
43
)
• Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Computer,
Video or S-Video). (
→
page
19
) If there is still no picture, press the button again.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. (
→
page
38
)
• Check to see if the image is muted. (
→
page
28
)
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the [Reset] in the Menu. (
→
page
45
)
• Enter your registered keyword if the Security function is enabled. (
→
page
28
)
• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
• See also the next page.
• When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
* When there are no signals (blue or black screen)
→
To return to the Normal mode, select another available
source.
* When the room where you' re presenting is particularly warm
→
Move the projector to a cooler location.
• Check if an appropriate color is selected in [Wall Color]. If not, select an appropriate option. (
→
page
40
)
• Adjust [Hue] in [Picture]. (
→
page
38
)
• Reposition the projector to improve its angle to the screen. (
→
page
20
,
21
)
• Use the Keystone correction function to correct the trapezoid distortion. (
→
page
25
)
• Make sure that focus is appropriate.
• Reposition the projector to improve its angle to the screen. (
→
page
20
,
21
)
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. (
→
page
10
)
• Make sure that the distance between the focus sensor and the screen is within the effective range of the Auto
Focus. (
→
page
22
)
• Make sure that the requirements for the Auto Focus are met. (
→
page
22
)
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
• Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Video, S-
Video or Computer). (
→
page
19
)
• Adjust the computer image manually with the Horizontal and Vertical in the [Image Options]
→
[Position/
Clock]. (
→
page
39
)
• Install new batteries. (
→
page
8
)
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. (
→
page
8
)
• See the POWER/STATUS/LAMP Indicator. (
→
page
50
)
• Press the AUTO ADJ. button on the projector cabinet or the remote control. (
→
page
26
)
• Adjust the computer image manually with [Clock] and [Phase] in [Image Options]
→
[Position/Clock] in the
menu. (
→
page
39
)
Problem
Check These Items
For more information contact your dealer.
