NDD easyone pro Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 188

NDD easyone pro Скачать руководство пользователя страница 19

EasyOne Pro™ / EasyOne Pro™ LAB

19

Introduction

Warning

Improper handling of gas cylinders represents a major risk to
persons and the environment. The relevant regulations must
be observed without exception. Protect the gas cylinders
from falling. The content and fill level must be clearly visible
at all times. Valves, fittings, connections and tubing must be
free of oil and grease. Have the cylinder inspected regularly
by an official test authority. The user is liable for any
damage. Close the main valve whenever the gas cylinder is
not in use!

FRC Gas (100% O

2

),

EasyOne Pro™ LAB

only

Medical grade oxygen; 100 % O

2

. From compressed gas cylinders or the

hospital's oxygen supply system.

Note

When using the wall outlet, please observe the hospital's in-
house instructions and requirements.

«
...
17
18
19
20
21
...
»

Содержание easyone pro





























































































































































































Отзывы:

Нет отзывов