NDD easyone pro Скачать руководство пользователя страница 130

Страница: 130 / 188

Troubleshooting Tips

130

EasyOne Pro™ / EasyOne Pro™ LAB

Troubleshooting Tips

Should you encounter problems operating your system, please consult the
table below for troubleshooting tips.

Note

The most recent information and frequently asked questions
can be found on our web site at www.ndd.ch.

When the

EasyOne

Pro™

is switched

on, you see the fol-
lowing error mes-
sage on the display

Self-test failed

Quit the program and
restart. If you receive
the same message
again, contact your
ndd dealer.

When you start a
test, you see the
message

Check

spirette insertion.

The

spirette™

is not

correctly positioned.

Ensure that the trian-
gle on the spirometer
is lined up with the tri-
angle on the

spirette™

Calibration check
outside ±3.5%.

The

spirette™

is not

correctly positioned.

Insert the

spirette™

described in section

"Inserting the One-Way
Valve, DLCO barri-
ette™/FRC barriette™
and spirette™"

page 35.

You have not used an
ndd adapter.

Use the ndd calibra-
tion adapter.

There are leaks in the
syringe connection.

Check the connec-
tions.

The specified syringe
volume differs from
the actual syringe vol-
ume.

Choose the correct
syringe volume via

Configuration

Test

Cal-Check

Содержание easyone pro





























































































































































































Результаты поиска

Содержание easyone pro

Отзывы:

NDD easyone pro, Руководство оператора, Страница: 130 / 188

Результаты поиска

Содержание easyone pro

Отзывы: