manualshive.com logo in svg

NDD easyone pro, Руководство оператора, Страница: 13 / 188

Поделиться
Скачать
NDD easyone pro Скачать руководство пользователя страница 13

 

EasyOne Pro™ / EasyOne Pro™ LAB

13

Introduction

EasyOne Pro™ LAB 

only

Danger

Explosion Hazard—

Ensure that persons working with oxygen have undergone 
special training and are aware of the particular properties 
of oxygen to guarantee safe handling of oxygen without 
accidents. Furthermore, these persons must be familiar 
with this operator manual and must have understood its 
content.

Do not use hand cream or other skin care products.

Oxygen intensively promotes combustion; therefore, 
flammable substances must be kept away from oxygen.

Unintended release of oxygen in confined spaces 
increases risk of fire; smoking and open flames are 
prohibited. Possible sources of ignition must be 
eliminated. Rooms must be well ventilated.

The oxygen inlet must periodically be checked for leaks 
(at least once a month).

Use only fittings approved for use with oxygen; these 
fittings must be properly connected. All fittings, 
downstream lines and devices must be free of oil and 
grease.

Connect a pressure relief valve to the pressurized gas 
cylinder before opening it! Before connecting the 
pressure relief valve, check the connection sleeve of the 
pressurized gas cylinder for contamination. Contaminated 
connections must be cleaned with a clean cloth. The valve 
of the pressurized gas cylinder may be opened only if the 
connected fittings are closed. Open the valve of the 
compressed gas cylinder very slowly.

Содержание easyone pro





























































































































































































Отзывы:

Нет отзывов