NDD easyone pro Скачать руководство пользователя страница 129

Страница: 129 / 188

EasyOne Pro™ / EasyOne Pro™ LAB

129

System Settings

Environment

Tab

On this tab you enter the ambient conditions. These will be overwritten by
values entered prior to the test (see

"FVL Test (inspiratory and expiratory

measurement)"

on page 51).

Fig. 8-22 Environment tab

a b c d e

h i

a Boxes for entry of room temperature,

relative humidity and altitude (above
sea level) of the examination site

b Measured values for room tempera-

ture, relative humidity, altitude (above
sea level), and case temperature

c BTPS conversion factor
d ATPS values will be used, yes/no (no

BTPS conversion)

e Select the check box, if you do not want

to enter ambient conditions for two
hours or until a restart. Otherwise,

remove the check mark by clicking
again.

f The values entered at a will be used for

BTPS calculation.

g Sensor case temperature
h Click to close the window, saving the

data

i Recalculate BTPS conversion factor

(e.g. after a change of the ambient con-
ditions)

Содержание easyone pro





























































































































































































Результаты поиска

Содержание easyone pro

Отзывы:

NDD easyone pro, Руководство оператора, Страница: 129 / 188

Результаты поиска

Содержание easyone pro

Отзывы: