NBK EPU-220 Скачать руководство пользователя | Manualshive

Страница: 37 / 52

background image

36

To ensure safe operation, be sure to perform inspections on a monthly basis.
If any abnormality is found, immediately stop operation and do not restart until the issue has been
resolved.

5.1 Precautions for Inspection

・

The operator shall be responsible for turning the power on and off.

・

Do not touch the unit during or immediately after operation as it may be extremely hot.

・

Be sure to carry out inspection in order to prevent accidents.

・

The standard service life is 300 hours of operation. Although this may vary depending on
the environmental and operating conditions, immediately replace the unit if an abnormality
occurs after the standard service life has elapsed.

5.2 Inspection Checklist

□

Is the power supply voltage within the specified range?

□

Is the operating environment within the specification ranges?

□

Is there an abnormality such as abnormal odor or noise?

□

Is there adhesion of dust or other foreign material?

□

Are any fastening parts such as the output shaft, the feed screw, or connectors loose?

□

Is any cable damaged or excessively stressed?

□

Is there any scratch or deformation on the main unit?

5

Maintenance

«
...
35
36
37
38
39
...
»

Содержание EPU-220





















































Отзывы:

Нет отзывов

Похожие инструкции для EPU-220

The Rook CryoAdvance 100

Бренд: Montana Instruments Страницы: 56

Бренд: ITT Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды