Navien NCB500-1.5S/37K страница 52 Скачать руководство пользователя

Страница: 52 / 72

Operating the Boiler 51

10.8 Error Codes

When an error code appears on the front panel, refer to the following chart for a definition and possible remedy for the situation.

Item

Error Code

Description

Reset

Combustion

E001

Overheating of heat exchanger

Manual

E003

Ignition failure

Manual

E004

False flame detection

Auto

E012

Flame loss

Manual

E016

Heat exchanger overheat

Manual

E030

Abnormal exhaust temperature

Manual

E046

Abnormal operation: Heat exchanger overheating sensor

Auto

E047

Abnormal operation: Exhaust thermostat

Manual/Auto

Air Circulation

E109

Abnormal operation: Fan

Manual

Central Heating

Circulation

E205

Heating supply thermistor open or short circuit

Auto

E218

Heating return thermistor open or short circuit

Alarm

E291

Supply/Return inversion limit

Manual Reset

Water Supply

E302

Low water pressure

Auto

E352

High water pressure

Auto

E353

Abnormal operation: Water pressure sensor

Auto

DHW Circulation

E407

DHW Outlet thermistor Open or Short Circuit

Alarm

E421

DHW Inlet thermistor Open or Short Circuit

Auto

E434

Abnormal operation: Flow control value

Alarm

E441

DHW Outlet 2 thermistor open or short circuit

Alarm

E445

Abnormal operation: Mixing valve

Alarm

E480

DHW tank thermistor open or short circuit

Alarm

Controller (PCB)

E515

Abnormal operation: Relay feedback (PCB)

Manual

E517

Abnormal operation: DIP switch setting (PCB)

Manual

E594

Abnormal operation: EEPROM (PCB)

Alarm/Manual

E598

Abnormal operation: Panel real time clock

Alarm

Controller (MCU)

E615

Abnormal operation: Input and memory (MCU)

Manual

Installation

E740

Abnormal operation: Outdoor temperature sensor

Auto

E782

Abnormal operation: Main panel communication

Auto

E783

Abnormal operation: OpenTherm remote control

Auto

E787

Abnormal operation: Reset device

Manual/Power Reset

E788

Abnormal operation: Gas type settings

Manual

If the error code is not cleared by resetting the boiler functioning (see “10.5 Resetting the Boiler”) or if it occurs repeatedly, call the nearest

official Technical Assistance Service (TAS), indicating the number of the error code appearing on the front panel.

Содержание NCB500-1.5S/37K









































































Результаты поиска

Содержание NCB500-1.5S/37K

Отзывы:

Похожие инструкции для NCB500-1.5S/37K

Бренды по названию

Популярные бренды

Navien NCB500-1.5S/37K, Руководство по установке и эксплуатации

Результаты поиска

Содержание NCB500-1.5S/37K

Отзывы:

Похожие инструкции для NCB500-1.5S/37K

Бренды по названию

Популярные бренды