background image

34        Flue System

WARNING

Improper flue of the boiler can result in excessive levels of 

carbon monoxide, which can lead to severe personal injury. 

Flue should be performed only by a licensed professional.

No specific ventilation is required in the room the boiler is 

installed in. If it is installed in a cupboard or compartment, no 

specific ventilation is required, providing the aforementioned 

dimensions are observed. The flue gas outlet and air supply 

installation must comply with the current regulation 

requirements in accordance with BS 5440 Part 1 and 2, and any 

other applicable legislation in this field must be observed.

6.1    Flue Terminal Positions

CAUTION

 

The terminal must be fitted with suitable protection if it 

is less than 2 m from a balcony, on a flat roof or surface 

that could be accessed by people.

 

The wall that the gas removal and air intake ducts are 

fixed to must not be made of combustible or flammable 

materials. The wall that the end of the duct passes 

through must lead to the outside of the home. There 

must be no hazardous materials or obstructions near the 

duct.

 

If the outlet passes through a wall made of combustible 

material the end terminal must be covered with at least 

20 mm of incombustible material and must maintain a 

distance of at least  

50 mm from any flammable material.

 

The parts connecting the flue outlet must be correctly 

joined using sealing gaskets. Ensure that there are no 

leaks from any part of the removal circuit.

 

Switch off the boiler and wait for the pipes to cool down 

before cleaning the gas removal and air intake ducts.

 

The gas removal and air intake ducts must be protected 

from snow accumulation.

The installation of the flue exhaust and combustion air intake 

system must be calculated and installed by a sufficiently 

qualified person. On designing and mounting the installation, 

the flue gas exhaust outlet and air supply installation must 

comply with the current regulation requirements in accordance 

with BS 5440, any other applicable legislation and stipulations 

applicable at the time of installation must be taken into account.

6.    Flue System

Содержание NCB300-28K



















































































Отзывы: