Nautel Exporter Plus Скачать руководство пользователя страница 183

Страница: 183 / 186

Exporter Plus Technical Instruction Manual

List of terms

Issue 1.0 2020-05-05

Page 11-1

Section 11:

List of terms

This section defines some of the terms that are used in Nautel documentation.

AAS.

Advanced Application Services

AES-EBU.

Audio Engineering Society/European Broadcasting Union (AES/EBU) is the name

of a digital audio transfer standard. The AES/EBU digital interface is usually implemented

using 3-pin XLR connectors (the same type of connector used in professional microphones).

One cable carries both left- and right-channel audio data to the receiving device.

Cat-5.

Short for Category 5. Network cabling that consists of four twisted pairs of copper wire

terminated by RJ45 connectors.

EOC.

Ensemble Operations Center.

EXGINE

An HD™ Radio component which resides in the exciter. The Exgine decodes the

Exciter link data and produces the appropriate I/Q modulation.

GPS.

The Global Positioning System is a system of satellites and receiving devices used to

compute positions on the Earth.

GUI

Graphical User Interface

™

Radio.

High definition (HD) Radio is another term for In Band On Channel (IBOC)

technology. HD Radio is a trademark of the Ibiquity Digital Corporation.

IBOC.

Nautel In-Band-On-Channel technology provides high quality digital audio over existing

AM and FM radio channels.

IRSS.

Ibiquity Reference System Software.

LAN.

Local Area Network.

MPS.

Main Program Service

NE IBOC.

Nautel’s In-Band-On-Channel signal generator. See IBOC. Required for XR series

IBOC installations.

PAD.

Program-Associated Data.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 183 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: