Nautel Exporter Plus Скачать руководство пользователя страница 170

Страница: 170 / 186

Exporter Plus Technical Instruction Manual

Troubleshooting

Page 10-4

Issue 1.0 2020-05-05

Figure 10.3: Typical Ping Command

Program service data (PSD)

If the Exporter Plus does not seem to be accepting program service data (PSD) from an

automation system, troubleshoot as follows:

1. Verify the destination IP address in the automation system matches the IP address of

the Exporter Plus.

2. If the automation system is not on the same subnet as the Exporter Plus, verify that the

automation system’s routing table contains an entry for the Exporter Plus IP address.

3. Verify the PSD port number in the automation system is set to 11000.

4. Verify the automation system PSD generator supports IRSS 4.2.x and higher HD

systems.

Exciter link

The Exporter Plus will automatically generate IBOC data provided that the exciter IP address

is not 0.0.0.0 and that audio is connected to the digital audio input (or to the analog input if

configured to use only a single input).

1. If the exciter is not on the same subnet as the Exporter Plus, make sure that the

Exporter Plus gateway is configured to the IP address of the local router to the exciter

subnet.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 170 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: