natus OLYMPIC STERILE-DRIER 43 Скачать руководство пользователя страница 47

Страница: 47 / 62

OLYMPIC STERILE-DRIER

Model 43/44 Instruction Manual

7-1

S e c t i o n

Replacement Parts

Ordering Information

To order parts and accessories, contact:

Natus Medical Incorporated
Customer Service Department

Toll-free: 1-800-303-0306
Phone:

+1-650-802-0400

Fax:

+1-650-802-6620

Email:

[email protected]

Parts and Accessories

When ordering, provide the item number and your Drier’s model number to the
customer service representative.

NOTE

Only use Natus Medical–approved parts with the Drier.

Table 7.1

Parts and accessories

Item Name / Description

Item Number

Accessories

Drying arms, regular (set of 8)

54357

Drying arms, narrow (set of 8)

54358

Olympic bag drier (dries up to 16 bags)

54355

Tube holder (holds 35 tubes)

54307

Tray

54302

Half tray

54304

Tray support (set of 2)

54306

Vent adapter, rear

500018

Vent adapter, side

500019

Parts

Arm repair kit, bag drier

400578

Autotransformer (100V~)

401146

Autotransformer (220-230V~)

200102

Blower assembly, 50Hz

401163

Содержание OLYMPIC STERILE-DRIER 43































































Результаты поиска

Содержание OLYMPIC STERILE-DRIER 43

Отзывы:

natus OLYMPIC STERILE-DRIER 43, Инструкция по эксплуатации, Страница: 47 / 62

Результаты поиска

Содержание OLYMPIC STERILE-DRIER 43

Отзывы: