natus ErgoJust ICU Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 92

natus ErgoJust ICU Скачать руководство пользователя страница 9

August 22, 2017

1-1

Chapter 1

Introduction

The Natus ErgoJust and Natus ErgoJust ICU are ergonomic carts used with Natus NeuroWorks/
SleepWorks devices and accessories to provide a complete portable workstation for EEG
applications.

The ErgoJust cart provides a portable workstation at the point of care in any hospital room
requiring EEG monitoring or testing. It is ideally designed for as a comprehensive solution for
long-term EEG monitoring (LTM). It features mounting brackets for Natus amplifier base units,
acquisition computer with NeuroWorks/SleepWorks software, a monitor, pan-tilt-zoom (PTZ) or
high-definition (HD PTZ) video camera options, IR light and microphone, Natus photic stimulator,
isolation transformer (ISO) or uninterruptible power supply (UPS) and basket(s) for clinical
supplies.

The ErgoJust ICU cart is ideal for EEG monitoring applications in an Intensive Care Unit (ICU). It
offers the same features as the ErgoJust cart but utilizes an All-in-One desktop acquisition
computer, ideal for a smaller footprint, touchscreen operation in the ICU.

ErgoJust and ErgoJust ICU features and options include:

•

Height adjustable work surface and
keyboard tray

•

Adjustable and tilting monitor

•

Sit-to-stand adjustment range

•

Quick disconnect attachment for Natus
amplifier base units

•

Computer with Natus Neuroworks/
SleepWorks software

•

Fixed -zoom, pan-tilt-zoom (PTZ) and
high-definition (HD) PTZ video camera

•

Small footprint base

•

4-wheel lockable casters

Natus ErgoJust and
ErgoJust ICU cart
dimensions

Cart with Video Pole

: 77.4” H x 22” W x 31” D (1.966m H x 0.558m W x 0.787m D)

«
...
7
8
9
10
11
...
»

Содержание ErgoJust ICU





























































































Отзывы:

Нет отзывов