Fiber Optic Products Instructions
For indoor use only. Retain carton for storage purposes.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Do not use seasonal products outdoors
unless marked suitable for indoor and
outdoor use. When products are used in
outdoor applications, connect the product to
a Ground Fault Circuit Interrupter (GFCI)
outlet. If one is not provided, contact a
qualified electrician for proper installation.
• This seasonal use product is not intended
for permanent installation or use.
• Do not mount or place near gas or electric
heaters, fireplaces, candles or other similar
sources of heat.
• Do not secure the wiring of the product
with staples or nails, or place on sharp
hooks or nails.
• Do not let lamps rest on the supply cord or any wire.
• Unplug the product when leaving the house,
when retiring for the night, or if left unattended.
•
CAUTION:
This is an electrical product – not a
toy! To avoid risk of fire, burns, personal injury
and electric shock, it should not be played with
or placed where small children can reach it.
• Do not use this product for other than its
intended use.
• Do not hang ornaments or other objects from
cord, wire or light string.
• Keep this product in a well ventilated area, do
not block any air openings.
• Do not close doors or windows on the product
or extension cords as this may damage the
wire insulation.
• Do not cover the base with paper, cloth or any
other material not part of the product when it
is in use.
• Never operate this product if the power cord
or plug is damaged.
• This product should not be used with a voltage
converter.
• Use only manufacturer specified replacement
bulbs.
• Do not look directly at any halogen bulb.
• Read and follow all instructions that are on the
product or provided with the product.
CAUTION:
IMPORTANT SAFETY INSTRUCTIONS
Note that some models will have the power supply adapter attached to
the base.
1. Place the base on a sturdy flat surface and insert the upper section
center pole into the center opening of the base. Push the upper
section in until it is firmly seated.
Taller trees will include a metal stand rather than a base pot (light
and motor assembly are attached to bottom of tree center pole).
Swivel the stand to its fully open position. Put section pole into tree
stand making sure it is seated properly (Figure 1). Tighten eye bolt.
2. The tree/topiary/bush can now be shaped by bending and arranging
the branches into desired positions giving it a natural appearance.
(The branches are folded in for shipping purposes.) See shaping
instructions below.
The base should never be covered with a tree skirt or similar
covering that may block the ventilation holes.
3. Plug the power supply adapter jack into the base (where applicable).
The adapter jack must be plugged into the base before being
plugged into a power outlet.
Plug the power supply adapter into a
standard outlet.
Multi-function models will have an additional electrical connection
between the upper section and base. Plug the wire connector from
the upper section into the socket on the top of the base (Figure 2).
Base Assembly
(where applicable)
Figure 3. Some models of taller fiber optic trees will have
bases that require separate legs to be attached. Referring
to the diagram, slide each leg up into the base as follows:
Line up the pegs on the lower section of leg with the holes
in the bottom of the base. Hold the leg against the base
wall and slide it up until the pegs are in the holes; at the
same time, the tab on the top of the leg will insert into the
slot beneath the ring at the top of the base.
Depending on base design, there will be three or four legs.
Install threes legs as shown in diagram. Use holes opposite
of each other for four leg models.
Branch Shaping
Figure 4
Shaping the branches of your product is the last step of
Figure 1
Figure 2
Figure 4
assembly. The care and attention you give to this final process will result
in a genuinely beautiful and appealing holiday centerpiece.
AC adapter should be disconnected from power source.
1. Make sure the fiber optic tree, topiary or bush is firmly seated in it’s
base.
2. Starting at the bottom of the product, fold down each individual
branch to it’s natural position. Continue working your way up, folding
down branches on top of the ones below (Figure 3).
Branches should be carefully pressed back to center when disassembled
for storage in original carton.
Figure 3
