background image

CALIBRATION PROCEDURE

NI USB-443

x

This document contains information about calibrating the National Instruments USB-4431 and 
USB-4432. These devices are referred to in this document as NI USB-443x. For more information about 
calibration, visit 

ni.com/calibration

.

Contents

Software Requirements........................................................................................................................ 2
Documentation Requirements.............................................................................................................. 2
Calibration Interval .............................................................................................................................. 2
Test Equipment .................................................................................................................................... 3
Test Conditions .................................................................................................................................... 4
Calibration Procedures......................................................................................................................... 4

Initial Setup.................................................................................................................................. 4
Changing Coupling on NI USB-443x Devices............................................................................ 5
Verification .................................................................................................................................. 6

Analog Input Performance Verification .............................................................................. 6

AI Offset Verification ................................................................................................. 6
AI AC Coupled Gain Accuracy Verification .............................................................. 7
AI DC Coupled Gain Accuracy Verification .............................................................. 8

Analog Output Performance Verification............................................................................ 10

AO Offset Verification for the NI USB-4431 Device  ................................................ 10
AO Gain Verification for the NI USB-4431 Device  .................................................. 11

Timebase Frequency Accuracy Verification ....................................................................... 12

Adjustment................................................................................................................................... 13

Analog Input Adjustment..................................................................................................... 13
Analog Output Adjustment for the NI USB-4431 Device................................................... 16

Where to Go for Support ..................................................................................................................... 18

ni.com/manuals

De

u

tsch

Français

Содержание USB-443 Series



















Отзывы: