manualshive.com logo in svg

National Instruments SCXI -1124, Руководство пользователя, Страница: 14 / 54

Поделиться
Скачать
National Instruments SCXI -1124 Скачать руководство пользователя страница 14

Introduction

Chapter 1

SCXI-1124 User Manual

1-4

© National Instruments Corporation

Always consider using NI-DAQ, LabVIEW, or LabWindows to program your National
Instruments data acquisition hardware.  Using the NI-DAQ, LabVIEW, or LabWindows software
is easier than, and as flexible as register-level programming, and can save you weeks of
development time.

Complete instructions for programming your module or DAQ board with NI-DAQ, LabVIEW,
or LabWindows are in the corresponding software manuals.  If you are using NI-DAQ,
LabVIEW, or LabWindows to control your board, you should not need the register-level
programmer manual.  The SCXI-1124 Register-Level Programmer Manual contains low-level
programming details, such as register maps, bit descriptions, and register programming hints,
that you will need only for register-level programming.  If you want to obtain the register-level
programmer manual, please fill out the Register-Level Programmer Manual Request Form at the
end of this manual and send it to National Instruments.

Optional Equipment

Equipment

Part Number

SCXI-1325 front terminal block

776573-25

SCXI-1340 cable assembly

776574-40

SCXI-1341 Lab-NB/Lab-PC/Lab-PC+ cable assembly

776574-41

SCXI-1342 PC-LPM-16 cable assembly

776574-42

SCXI-1343 rear screw terminal adapter

776574-43

SCXI-1344 Lab-LC cable assembly

776575-44

SCXI-1345 SCXI shielded cable assembly

with 1 m cable
with 2 m cable
with 5 m cable
with 10 m cable

776574-451
776574-452
776574-455
776574-450

SCXI-1347 SCXI shielded cable assembly

with 1 m cable
with 2 m cable
with 5 m cable
with 10 m cable

776574-471
776574-472
776574-475
776574-470

SCXI-1348 DIO-32F cable assembly

776574-48

SCXI-1350 multichassis adapter

776575-50

SCXI-1351 one-slot cable extender

776575-51

Standard ribbon cable

0.5 m
1.0 m

180524-05
180524-10

NB5 cable

0.5 m
1.0 m

181304-05
181304-10

NB6 cable

0.5 m
1.0 m

181305-05
181305-10

Refer to Chapter 3, Signal Connections, the accessory installation guides, and the National
Instruments Catalog for additional information on cabling, connectors, and adapters.

Содержание SCXI -1124























































Отзывы:

Нет отзывов