National Instruments PXIe-4353 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 20

National Instruments PXIe-4353 Скачать руководство пользователя страница 9

©

National Instruments Corporation

9

NI PXIe-4353 and TB-4353 Terminal Block Installation Guide

Tip

Using an NI-DAQmx simulated device, you can test NI-DAQmx applications without installing

hardware. Refer to the

Create a Simulated Device

section for instructions for creating NI-DAQmx

simulated devices.

3.

Right-click the module name and select

Self-Test

. When the self-test completes, a verification

message appears. If an error occurs, refer to

ni.com/support/daqmx

.

For information about sensors, go to

ni.com/sensors

.

Step 6. Run Test Panels

1.

In MAX, expand

Devices and Interfaces»NI-DAQmx Devices

.

2.

Right-click the device, and select

Test Panels

.

3.

Click

Start

to test device functions, or

Help

for operating instructions.

To troubleshoot errors, refer to the

NI-DAQmx Help

, or go to

ni.com/support

.

Step 7. Take an NI-DAQmx Measurement

NI-DAQmx Channels and Tasks

Refer to the

NI-DAQmx Help

for complete information about channels and tasks.

Use the DAQ Assistant to configure virtual channels and tasks in MAX or in your application.

«
...
7
8
9
10
11
...
»

Содержание PXIe-4353





















Отзывы:

Нет отзывов