National Instruments PXIe-1088 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 26

National Instruments PXIe-1088 Скачать руководство пользователя страница 18

DIP Switches

The backplane has a DIP switch that may be used to control chassis behavior.

DIP switch #1 (first from the bottom) controls the chassis fan mode. When this switch is in the
off (right) position, Auto mode is selected. When this switch is in the on (left) position, High
mode is selected.

DIP switch #2 (second from the bottom) controls the chassis Inhibit Mode. When this switch is
in the off (right) position, Default mode is selected. When this switch is in the on (left)
position, Manual mode is selected.

Figure 12. Backplane DIP Switches

1

2

3

4

1. Switch #1 (Fan)
2. Switch #2 (PWR)

3. Switch #3 (NC)
4. Switch #4 (NC)

Table 3. DIP Switch States

Location Switch

State

Description

1

FAN

Off (Right) Set chassis fan mode to Auto. Refer to the

Fan Mode

section for information.

On (Left)

Set chassis fan mode to High.

2

PWR

Off (Right) Set chassis inhibit mode to Default. Refer to the

Inhibit

Mode

section for information

On (Left)

Set chassis inhibit mode to Manual.

3

NC

-

-

4

NC

-

-

18

|

ni.com

|

PXIe-1088 User Guide

«
...
16
17
18
19
20
...
»

Содержание PXIe-1088



























Отзывы:

Нет отзывов