National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Скачать руководство пользователя | Manualshive

Страница: 61 / 83

background image

©

National Instruments Corporation

5-1

NI PXI-8108 User Manual

5

Troubleshooting

This chapter answers common troubleshooting questions you may have
when using the NI PXI-8108 embedded computer.

What if the NI PXI-8108 does not boot?

Several problems can cause a controller not to boot. Here are some things
to look for and possible solutions.

Things to Notice

:

•

Which LEDs come on? The

Power OK

LED should stay lit.

The

Drive

LED should blink during boot as the disk is accessed.

•

Was the display installed prior to power-on? What appears on the
display? Does it hang at some particular point (BIOS, Operating
System, and so on)? If nothing appears on the screen, try a different
monitor. Does your monitor work with a different PC? If it hangs, note
the last screen output that you saw for reference when consulting
National Instruments technical support.

•

What has changed about the system? Did you recently move the
system? Was there electrical storm activity? Did you recently add
a new module, memory chip, or piece of software?

Things to Try

:

•

Make sure the chassis is plugged in to a working power source.

•

Check any fuses or circuit breakers in the chassis or other power
supply (possibly an uninterruptible power supply).

•

Make sure the controller module is firmly seated in the chassis.

•

Remove all other modules from the chassis.

•

Remove any nonessential cables or devices.

•

Try the controller in a different chassis.

•

Try a similar controller in this same chassis.

•

Clear the CMOS. (Refer to the

section of Chapter 2,

Installation and Configuration

.)

•

Recover the hard drive on the controller. (Refer to the

section of Chapter 2,

Installation and Configuration

.)

«
...
59
60
61
62
63
...
»

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108




















































































Отзывы:

Нет отзывов

Похожие инструкции для PXI/CompactPCI Embedded Computer NI PXI-8108

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Zolix Instruments Страницы: 22

Бренд: S-COM Страницы: 400

Бренд: Campbell Страницы: 34

Flashlight Blue

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 4

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 5

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 6

Бренд: WAM Страницы: 62

Бренд: walimex Страницы: 7

Бренд: Walchem Страницы: 2

Бренд: Walchem Страницы: 73

Бренд: Walchem Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды