National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Скачать руководство пользователя | Manualshive

Страница: 39 / 83

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-25

NI PXI-8108 User Manual

Installing an OS

NI PXI-8108 controllers include a pre-installed OS. In some cases, you
may want to install a different OS. When doing so, consider the following
guidelines.

Installing from a CD-ROM

The NI PXI-8108 supports the installation of Windows XP and Vista from
a USB CD-ROM.

As an alternative to a USB CD-ROM drive, you can use an external SCSI
CD-ROM with a PXI-SCSI adapter.

Note

For additional assistance with installing or changing an operating system, refer to

KnowledgeBase 2ZKC02OK at

ni.com/support

.

ExpressCard

This section provides information on the installation and removal of
ExpressCard modules.

Installing an ExpressCard

You can install an ExpressCard module while the NI PXI-8108 is running.
The NI PXI-8108 will automatically detect the card. ExpressCards are
generally marked with a symbol or a label to indicate which end to insert
into the slot. The cards are keyed to prevent incorrect insertion.

To install an ExpressCard, complete the following steps.

1.

Hold the card so the top side is facing left.

2.

Insert the card until it is completely seated in its connector. The
connector has an automatic eject mechanism. If you insert the card and
it is ejected, simply re-insert the card until it is seated.

If you encounter too much resistance, do not force the card. Check the card
orientation and try again.

The PXI-8108 will automatically recognize the ExpressCard and load the
appropriate driver(s). Third-party cards may require that you install
additional drivers. Contact your ExpressCard vendor for more information.

«
...
37
38
39
40
41
...
»

Содержание PXI/CompactPCI Embedded Computer NI PXI-8108




















































































Отзывы:

Нет отзывов

Похожие инструкции для PXI/CompactPCI Embedded Computer NI PXI-8108

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Eaton Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Trane Technologies Страницы: 8

SmarTemp Control fx

Бренд: Webasto Страницы: 8

Бренд: Jeckson Electric Страницы: 2

Бренд: Yoshitake Страницы: 21

Бренд: Oasis Страницы: 7

Бренд: M-system Страницы: 7

Бренд: Texecom Страницы: 21

Бренд: CAME Страницы: 128

Comfort System Z-300-HC

Бренд: Jackson Systems Страницы: 2

FLECK 5810 XTR2

Бренд: Pentair Страницы: 36

Compact Performance Series

Бренд: Festo Страницы: 58

Grain PNEG-1509

Бренд: GSi Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды