National Instruments PXI-8186 Скачать руководство пользователя | Manualshive

Страница: 50 / 69

background image

©

National Instruments Corporation

5-1

NI PXI-8186 User Manual

5

Troubleshooting

This chapter answers common troubleshooting questions you may have
when using the NI PXI-8186 embedded computer.

What if the NI PXI-8186 does not boot?

Several problems can cause a controller not to boot. Here are some things
to look for and possible solutions.

Things to Notice

:

•

Which LEDs come on? The

Power OK

LED should stay lit.

The

Drive

LED should blink during boot as the disk is accessed.

•

What appears on the display? Does it hang at some particular point
(BIOS, Operating System, and so on.)? If nothing appears on the
screen, try a different monitor. Does your monitor work with a
different PC? If it hangs, note the last screen output that you saw for
reference when consulting National Instruments technical support.

•

What has changed about the system? Did you recently move the
system? Was there electrical storm activity? Did you recently add
a new module, memory chip, or piece of software?

Things to Try

:

•

Make sure the chassis is plugged in to a working power source.

•

Check any fuses or circuit breakers in the chassis or other power
supply (possibly a UPS).

•

Make sure the controller module is firmly seated in the chassis.

•

Remove all other modules from the chassis.

•

Remove any nonessential cables or devices.

•

Try the controller in a different chassis.

•

Try a similar controller in this same chassis.

•

Recover the hard drive on the controller. (Refer to the

section of Chapter 2,

Installation and Configuration

.)

•

Clear the CMOS. (Refer to the

section of Chapter 2,

Installation and Configuration

«
...
48
49
50
51
52
...
»

Содержание PXI-8186






































































Отзывы:

Нет отзывов

Похожие инструкции для PXI-8186

Бренд: Salus Страницы: 16

Бренд: Amperes Страницы: 8

Бренд: Pima Страницы: 4

Бренд: Delta Electronics Страницы: 1

Parallel Printer Card PIOC

Бренд: B&B Electronics Страницы: 16

Бренд: Rolls Страницы: 1

PowerMatch ESPLink

Бренд: Bose Страницы: 2

Total Access 1500 Dual FXS/DPO

Бренд: ADTRAN Страницы: 2

Бренд: FOR-A Страницы: 37

Бренд: Renesas Страницы: 4

DTS 4020.timebridge

Бренд: Mobatime Страницы: 94

ROADRECORDER 8400 NVR

Бренд: Safety Vision Страницы: 27

ibaBM-FOX-i-3o-D

Бренд: IBA Страницы: 13

VDA-NVR2108W4KS2

Бренд: Dahua Technology Страницы: 363

IQ Switch IQS128

Бренд: Azoteq Страницы: 4

Бренд: Orcomm Страницы: 10

Бренд: TRENDnet Страницы: 56

Ready Made Curtain

Бренд: Kvadrat Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды