National Instruments PXI-8110 Скачать руководство пользователя

Страница: 55 / 85

Chapter 3

I/O Information

NI PXI-8110 User Manual

3-14

ni.com

Front Panel Features

The NI PXI-8110 controller has the following front-panel features:

•

A controller reset pushbutton (press the button to generate a reset to the
controller)

•

Two front panel LEDs that show PC status

–

The

POWER OK

LED indicates the power status of the

controller. The LED will indicate one of the following states:

•

ON steady

—PXI and onboard power is on and within

regulation limits.

•

Blinking

—One of the PXI or onboard supplies is operating

outside of the normal limits, or is not functioning.

•

OFF

—The power to the controller is off.

–

The

DRIVE

LED indicates when an access to the internal hard

disk is occurring.

Data Storage

The NI PXI-8110 has the following data storage features:

•

2.5 in. SATA notebook internal hard drive

•

USB storage support—USB CD-ROM, mass storage device, or floppy
drive

Содержание PXI-8110






















































































Результаты поиска

Содержание PXI-8110

Отзывы:

Похожие инструкции для PXI-8110

Бренды по названию

Популярные бренды

National Instruments PXI-8110, Руководство пользователя

Результаты поиска

Содержание PXI-8110

Отзывы:

Похожие инструкции для PXI-8110

Бренды по названию

Популярные бренды