National Instruments PCI-6238 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 173

background image

Chapter 4

Analog Input

NI 6238/6239 User Manual

4-18

ni.com

•

RTSI <0..7>

•

Input PFI <0..5>

•

PXI_STAR

ai/SampleClockTimebase is not available as an output on the I/O connector.
ai/SampleClockTimebase is divided down to provide one of the possible
sources for ai/SampleClock. You can configure the polarity selection for
ai/SampleClockTimebase as either rising or falling edge.

AI Convert Clock Signal

Caution

Setting the conversion rate higher than the maximum rate specified for your

device will result in errors.

Use the AI Convert Clock (ai/ConvertClock) signal to initiate a single A/D
conversion on a single channel. A sample, controlled by the AI Sample
Clock, consists of one or more conversions.

You can specify either an internal or external signal as the source of
ai/ConvertClock. You also can specify whether the measurement sample
begins on the rising edge or falling edge of ai/ConvertClock.

With NI-DAQmx, the driver will choose the fastest conversion rate possible
based on the speed of the A/D converter and add 10 µs of padding between
each channel to allow for adequate settling time. This scheme enables the
channels to approximate simultaneous sampling and still allow for
adequate settling time. If the AI Sample Clock rate is too fast to allow for
this 10 µs of padding, NI-DAQmx will choose the conversion rate so that
the AI Convert Clock pulses are evenly spaced throughout the sample.

To explicitly specify the conversion rate, use the

AI Convert Clock Rate

DAQmx Timing

property node or function.

Using an Internal Source

One of the following internal signals can drive ai/ConvertClock:

•

AI Convert Clock Timebase (divided down)

•

Counter

n

Internal Output

A programmable internal counter divides down the AI Convert Clock
Timebase to generate ai/ConvertClock. The counter is started by
ai/SampleClock and continues to count down to zero, produces an
ai/ConvertClock, reloads itself, and repeats the process until the sample is

«
...
43
44
45
46
47
...
»

Содержание PCI-6238














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PCI-6238

Бренд: ICP DAS USA Страницы: 5

Бренд: ICP DAS USA Страницы: 7

Бренд: LAON TECHNOLOGY Страницы: 58

Бренд: RAPIBREW Страницы: 16

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Бренд: U-Line Страницы: 18

Бренд: Launch Страницы: 62

Бренд: Advantech Страницы: 82

USB-1408FS-Plus-OEM

Бренд: Measurement Computing Страницы: 26

Бренд: facelift Страницы: 8

Genie BBSKETDL15B-1001

Бренд: Terex Страницы: 69

Cruisair SMX II

Бренд: Taylor Made Environmental Страницы: 36

Бренд: b-red Страницы: 12

Бренд: welldana Страницы: 7

Бренд: SEW-Eurodrive Страницы: 384

Villa Door Station

Бренд: Dahua Страницы: 37

Бренд: Contec Страницы: 78

CPS-MC341-DS1 -111

Бренд: Contec Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды