National Instruments PCI-6238 Скачать руководство пользователя страница 104

Страница: 104 / 173

Chapter 7

Counters

NI 6238/6239 User Manual

7-38

ni.com

counter value and Counter

Internal Output signals change synchronously

to the 80 MHz Timebase.

Note that duplicate count prevention should only be used if the frequency
of the Source signal is 20 MHz or less.

When To Use Duplicate Count Prevention

You should use duplicate count prevention if the following conditions are
true.

•

You are making a counter measurement

•

You are using an external signal (such as PFI <0..5>) as the counter
Source

•

The frequency of the external source is 20 MHz or less

•

You can have the counter value and output to change synchronously
with the 80 MHz Timebase

In all other cases, you should

not

use duplicate count prevention.

Enabling Duplicate Count Prevention in NI-DAQmx

You can enable duplicate count prevention in NI-DAQmx by setting the

Enable Duplicate Count Prevention

attribute/property. For specific

information on finding the

Enable Duplicate Count Prevention

attribute/property, refer to the help file for the API you are using.

Synchronization Modes

The 32-bit counter counts up or down synchronously with the Source
signal. The Gate signal and other counter inputs are asynchronous to the
Source signal, so M Series devices synchronize these signals before
presenting them to the internal counter.

M Series devices use one of three synchronization methods:

•

80 MHz source mode

•

Other internal source mode

•

External source mode

In DAQmx, the device uses 80 MHz source mode if the user performs the
following:

•

Performs a position measurement

•

Selects duplicate count prevention

Содержание PCI-6238














































































































































































Результаты поиска

Содержание PCI-6238

Отзывы:

Похожие инструкции для PCI-6238

Бренды по названию

Популярные бренды

National Instruments PCI-6238, Руководство пользователя

Результаты поиска

Содержание PCI-6238

Отзывы:

Похожие инструкции для PCI-6238

Бренды по названию

Популярные бренды