background image

©

 National Instruments Corporation

9

NI 1357/1358/1359 Kit Installation Guide

Figure 8.  

Configuring the SCXI Chassis Configuration Dialog Box

5.

Configure the SCXI switch module:

a.

If you did not enable auto-detection of the switch module in 
step 4d, select an SCXI switch module from the 

Module Array

 

listbox. Assign the switch module the slot number that matches 
the physical slot location of the switch module in the chassis.

b.

MAX assigns a default name to the SCXI switch module in the 
Device Identifier textbox. The

Device Identifier

 is the 

resource name

 string in NI-SWITCH and the 

switch device

 

string in NI-DAQmx. To edit the default name, click the 

Device 

Identifier 

textbox and enter a unique alphanumeric ID for the 

switch module. 

c.

If you are using a connected accessory, such as a terminal block, 
select it from the 

Accessory

 listbox.

6.

Click 

Details

 to configure the switch module options. 

The Details dialog box for the switch module configuration dialog box 
opens. The 

Terminal Block/Topology

 tab is selected by default. 

7.

Configure the Details dialog box for an SCXI switch module:

Note

During scanning, the NI SCXI-1127/1128 can connect to the HVAB. To configure 

the switch module to automatically connect to the HVAB during scanning, enable the 
optional checkbox in the Details dialog box.

a.

Select the terminal block connected to the switch module from the 

Terminal Block/Topology

 listbox.

b.

Set a default topology from the 

Topology

 listbox.

Содержание NI SCXI 1357














Отзывы: