National Instruments NI SCXI-1336 Скачать руководство пользователя страница 12

Страница: 12 / 83

Chapter 1

Installing and Configuring the SCXI-1129

National Instruments Corporation

1-3

SCXI-1129 User Manual

Note

The

Interactive Support Only

choice does

not

allow you to program the instrument

with any programming languages.

For advanced users only

—

when installing NI-SWITCH, the

Development Environments

panel provides you with the following

choices:

•

If you click the

Advanced

button on this panel, you can custom

install National Instruments drivers such as NI-DAQ, NI-IVI, and
NI-VISA.

•

If you do

not

want to install certain drivers, click

Advanced

and

uncheck the driver(s) you do not want installed.

If a driver is already unchecked, your computer has the same driver or
a newer version of the driver already installed.

Note

If a newer version of a driver is present on your PC, the installer will

not

overwrite

the driver.

After completing the installation, power off your computer.

Safety Information

The following cautions contain important safety information concerning
hazardous voltages.

Cautions

not

operate the device in an explosive atmosphere or where there may be

flammable gases or fumes.

Keep away from live circuits. Do

not

remove equipment covers or shields unless you are

trained to do so. If signal wires are connected to the device, hazardous voltages can exist
even when the equipment is powered off. To avoid a shock hazard, do

not

perform

procedures involving cover or shield removal unless you are qualified to do so and
disconnect all field power prior to removing covers or shields.

Equipment described in this document

must

be used in an Installation Category I

environment per IEC 60664-1. This category requires local level supply mains-connected
installation.

not

operate damaged equipment. The safety protection features built into this device

can become impaired if the device becomes damaged in any way. If the device is damaged,

Category I refers to a signal level such as voltages of an isolation transformer secondary on a PWB.

Содержание NI SCXI-1336




















































































Результаты поиска

Содержание NI SCXI-1336

Отзывы:

Похожие инструкции для NI SCXI-1336

Бренды по названию

Популярные бренды

National Instruments NI SCXI-1336, Руководство пользователя

Результаты поиска

Содержание NI SCXI-1336

Отзывы:

Похожие инструкции для NI SCXI-1336

Бренды по названию

Популярные бренды