National Instruments NI PXIe-8130 Скачать руководство пользователя | Manualshive

Страница: 32 / 84

background image

Chapter 2

Installation and Configuration

NI PXIe-8130 User Manual

2-16

ni.com

•

Discard Changes and Exit

—Select this option to discard any changes

made to BIOS settings during this session of the BIOS setup program.
The setup program then exits and continues booting the controller
without restarting first. The <Esc> key can also be used to select this
option.

•

Discard Changes

—Select this option to discard any changes made to

BIOS settings during this session of the BIOS setup program without
also exiting the setup program. The <F7> key can also be used to select
this option.

•

Load Defaults

—Select this option to restore all BIOS settings to

the factory defaults. This option is useful if the controller exhibits
unpredictable behavior due to an incorrect or inappropriate BIOS
setting. Note that any nondefault settings such as boot order,
passwords, and so on, are restored to their factory defaults. The
<F9> key can also be used to select this option.

System CMOS

The NI PXIe-8130 contains memory backed up by a battery to store BIOS
configuration information.

Complete the following steps to clear the CMOS contents:

1.

Power off the chassis.

2.

Remove the controller from the chassis.

3.

Move the jumper on W2 from pins 1–2 to pins 2–3, as shown in
Figure 2-3.

4.

Wait one second. Move the jumper back to pins 1–2.

5.

Reinstall the controller in the chassis.

Caution

Do

not

leave the jumper on pins 2–3. Doing so decreases battery life and prevents

the controller from booting.

«
...
30
31
32
33
34
...
»

Содержание NI PXIe-8130





















































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8130

System x3630 M4

Бренд: IBM Страницы: 7

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 5

Бренд: Patton electronics Страницы: 8

Бренд: Belkin Страницы: 72

Бренд: LogLogic Страницы: 30

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренд: QuickLink Страницы: 8

D-NVR4108HS-4KS2/L

Бренд: Dahua Страницы: 33

Бренд: Xtreme Страницы: 83

Powereta iQP Series

Бренд: TDK Страницы: 2

Бренд: Renesas Страницы: 4

ULTRIX-FM-NS-1RU

Бренд: Ross Страницы: 5

Q-SYS QIO-GP8x8

Бренд: QSC Страницы: 13

Бренд: Vxl Страницы: 4

Бренд: Honeywell Home Страницы: 36

Бренд: XMOS Страницы: 8

Бренд: Rosewill Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды