National Instruments NI PXIe-8130 Скачать руководство пользователя | Manualshive

Страница: 24 / 84

background image

Chapter 2

Installation and Configuration

NI PXIe-8130 User Manual

2-8

ni.com

Primary IDE Master/Slave Submenus

Use these submenus to apply alternate settings to the primary IDE master
and slave interfaces. Normally, you do not need to modify these settings,
as the factory default settings provide the most compatible and optimal
configuration.

•

Type

—This setting specifies type of device that the BIOS attempts to

boot from. The default is

Auto

, which allows the BIOS to auto-detect

the type of device connected to the IDE interface.

•

LBA/Large Mode

—This setting specifies whether or not the BIOS

will use LBA mode on the IDE interface. LBA (Logical Block
Addressing) is a method of addressing data on a disk drive. In LBA
mode, the maximum drive capacity is 137 GB. The default is

Auto

,

which allows the BIOS to automatically detect whether or not to use
LBA mode.

•

Block (Multi-sector transfer)

—This setting specifies whether or not

block (multi-sector transfer) mode should be enabled. The default is

Auto

, which allows the BIOS to automatically detect whether or not

the device on the IDE interface supports block mode.

•

PIO Mode

—This setting specifies the Programmed I/O mode that

should be used on this IDE interface. As PIO mode increases, the cycle
time decreases. The default is

Auto

, which allows the BIOS to

automatically detect the PIO mode of the device attached to this IDE
interface.

•

DMA Mode

—This setting specifies the DMA mode that should be

used on this IDE interface. The default is

Auto

, which allows the BIOS

to automatically detect the DMA mode of the device attached to this
IDE interface.

•

S.M.A.R.T.

—This setting specifies whether or not the

Self-Monitoring Analysis and Reporting Technology feature is
enabled or disabled. This feature can be used to predict drive failures.
The default is

Auto

, which allows the BIOS to automatically

determine if the attached hard drive is SMART capable, and if so,
to enable the feature.

•

32Bit Data Transfer

—This setting specifies whether or not 32-bit

data transfers are enabled on supported hard disks. The default is

Enabled

.

«
...
22
23
24
25
26
...
»

Содержание NI PXIe-8130





















































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8130

Бренд: RadiSys Страницы: 44

Бренд: TFortis Страницы: 86

Бренд: ForeScout Страницы: 28

Бренд: Lanner Страницы: 109

Бренд: Telit Wireless Solutions Страницы: 113

ST62GP-EMU2 HDS2 Series

Бренд: STMicroelectronics Страницы: 58

Active Module Carrier VX402C-64

Бренд: C&H Страницы: 32

JetStor NAS 724UX

Бренд: AC&NC Страницы: 117

Бренд: ANEP Страницы: 48

PG-Flex FLC-704

Бренд: PairGain Страницы: 20

Бренд: Teridian Страницы: 2

MP5S Plus Writer

Бренд: SONIX Страницы: 23

NC-MCO - TECHNICAL

Бренд: Crest Audio Страницы: 2

Бренд: Kontron Страницы: 14

Бренд: Netopia Страницы: 138

Бренд: Alphacool Страницы: 9

BPN-SAS3-LB16A-N10

Бренд: Supermicro Страницы: 11

ServCon FPS-3003

Бренд: LevelOne Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды