National Instruments NI PXIe-8105 Скачать руководство пользователя

Страница: 8 / 76

About This Manual

viii

ni.com

monospace bold

Bold text in this font denotes the messages and responses that the computer
automatically prints to the screen. This font also emphasizes lines of code
that are different from the other examples.

Related Documentation

The following documents contain information you may find helpful as you
read this manual:

•

PICMG EXP.0 R1.0 CompactPCI Express Specification

, PCI

Industrial Computers Manufacturers Group

•

IEEE Standard P1284.1-1997

(C/MM) Standard for Information

Technology for Transport Independent Printer/System Interface

•

PCI Express Base Specification

, Revision 1.1, PCI Special Interest

Group

•

PXI-5 PXI Express Hardware Specification

, Revision 1.0, PXI

Systems Alliance

•

PXI-6 PXI Express Software Specification

, Revision 1.0, PXI Systems

Alliance

•

Serialized IRQ Support for PCI Systems Specification

, Revision 6.0,

Compaq Computer et al.

•

ExpressCard Standard

, Release 1.0, PCMCIA

Содержание NI PXIe-8105













































































Результаты поиска

Содержание NI PXIe-8105

Отзывы:

Похожие инструкции для NI PXIe-8105

Бренды по названию

Популярные бренды

National Instruments NI PXIe-8105, Руководство пользователя

Результаты поиска

Содержание NI PXIe-8105

Отзывы:

Похожие инструкции для NI PXIe-8105

Бренды по названию

Популярные бренды