National Instruments NI ISM-7401 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 31

National Instruments NI ISM-7401 Скачать руководство пользователя страница 29

NI ISM-7401/7402 User Manual

|

© National Instruments

|

29

Motor

Torque ............................................................... Refer to

Torque-Speed Curves

Digital Inputs

Optically isolated, 5 V to 24 V logic. Sourcing, sinking, or differential signals can be used. Drive
steps on falling edge of STEP+ input.

Minimum on voltage ........................................ 4 VDC

Maximum voltage............................................. 30 VDC

Input current ..................................................... 5 mA typ at 4 V,

15 mA typ at 30 V

Maximum pulse frequency: .............................. 150 kHz or 2 MHz (switch selectable)

Minimum pulse width....................................... 3

μ

s (at 150 kHz setting)

0.25

μ

s (at 2 MHz setting)

Fault Output

Photodarlington ................................................ 80 mA, 30 VDC max

Voltage drop...................................................... 1.2 V max at 80 mA

Physical

NI ISM-7401

Size ........................................................... 2.22 in. × 3.35 in.× 3.35 in.

(56.4 mm × 85 mm × 85 mm), not including
pilot or shaft. 0.25 in. shaft with flat.

Weight....................................................... 30 oz (850 g)
Rotor inertia.............................................. 3.68 × 10

-3

oz-in.-sec

2

(260 g-cm

2

)

NI ISM-7402

Size ........................................................... 2.22 in. × 3.35 in. × 4.21 in.

(56.4 mm × 85 mm × 107 mm), not including
pilot or shaft. 0.25 in. shaft with flat.

Weight....................................................... 42 oz (1200 g)
Rotor inertia.............................................. 6.52 × 10

-3

oz-in.-sec

2

(460 g-cm

2

)

Operating temperature range ............................ 0 °C to 40 °C

Incremental Encoder Specifications

10-pin connector signals (pin assignments)

Ground ..................................................... 1, 2
Index- ....................................................... 3
Index+ ...................................................... 4
A- ............................................................. 5

«
...
27
28
29
30
31
»

Содержание NI ISM-7401
































Отзывы:

Нет отзывов