National Instruments NI cDAQTM-9138 Скачать руководство пользователя | Manualshive

Страница: 10 / 141

background image

© National Instruments

|

1-1

1

Getting Started with the
cDAQ Chassis

The National Instruments CompactDAQ cDAQ-9138 stand-alone chassis with integrated
controller features the 1.06 GHz Celeron processor. The National Instruments CompactDAQ
cDAQ-9139 stand-alone chassis with integrated controller features the 1.33 GHz Intel Core i7
processor. The NI cDAQ-9138 and NI cDAQ-9139 are available as a Windows Embedded
Standard 7 (WES7) or a LabVIEW Real-Time system.

This chapter contains information about getting started with the cDAQ chassis with Windows
and with LabVIEW Real-Time:
•

For NI cDAQ-9138/9139 for Windows, refer to the

Installing the NI cDAQ-9138/9139 for

section

•

For NI cDAQ-9138/9139 for LabVIEW Real-Time, refer to the

Installing the

NI cDAQ-9138/9139 for LabVIEW Real-Time

section

The eight-slot cDAQ stand-alone chassis has a built-in controller with a number of standard
interfaces and combines with C Series I/O modules to measure a broad range of analog and
digital I/O signals that can be logged to the local hard drive. For specifications, refer to the
specifications document for your cDAQ chassis. For module specifications, refer to the
documentation included with your C Series I/O module(s) or go to

ni.com/manuals

.

Note

Go to

ni.com/info

and enter Info Code

exswh5

for up-to-date

information about supported NI devices for the cDAQ chassis.

«
...
8
9
10
11
12
...
»

Содержание NI cDAQTM-9138














































































































































Отзывы:

Нет отзывов

Похожие инструкции для NI cDAQTM-9138

Бренд: ABB Страницы: 52

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: 1Control Страницы: 8

Бренд: Baby Jogger Страницы: 24

Бренд: Baby Jogger Страницы: 16

city select LUX

Бренд: Baby Jogger Страницы: 20

CITY ELITE SINGLE

Бренд: Baby Jogger Страницы: 24

Бренд: Baby Jogger Страницы: 147

Бренд: GCE Страницы: 24

Бренд: Hanna Instruments Страницы: 88

Black Force Wireless

Бренд: Hama Страницы: 10

Бренд: Lamtec Страницы: 136

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: RADEMACHER Страницы: 68

Бренд: Klimaire Страницы: 5

S3500 Series Uplink Module

Бренд: Aruba Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды