manualshive.com logo in svg

National Instruments NI 9512, Инструкция по эксплуатации и технические характеристики

Поделиться
Скачать
National Instruments NI 9512 Скачать руководство пользователя страница 9

NI 9512 Operating Instructions and Specifications

|

© National Instruments

|

9

Table 1.  

NI 9512 Connection Options

Drive

Connection Option

NI ISM-7400/7401/
7402
NI SMD-7610
NI SMD-7611/7612
NI SMD-7620/7621

Direct Connectivity to NI ISM and NI SMD 
stepper drives
Go to 

ni.com/info

 and enter 

stepper

 

for 

installation and configuration information for 
NI ISM and NI SMD stepper drives.

AKD Analog Servo NI 9512 to AKD Drive Cable

(NI part number 781525-01)
Refer to 

Getting Started with NI 9512 C Series 

Drive Interface Modules and AKD Analog Servo 

Drives 

for installation and configuration 

information for AKD servo drives

Mitsubishi MR-J2 
or MR-J3

NI 9930M Motion Control Accessory
(NI part number 781824-01)
Refer to 

NI 9930 Motion Control Accessories 

User Guide

 for installation and configuration 

information for connection to Mitsubishi, 
p-command servo drives.

Содержание NI 9512













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды