National Instruments NI 4112 Скачать руководство пользователя

Страница: 1 / 18

CALIBRATION PROCEDURE

NI PXIe-4113

Dual-Output Programmable DC Power Supply

This document contains the verification and adjustment procedures for the NI PXIe-4113
(NI 4113). Refer to

ni.com/calibration

for more information about calibration solutions.

Contents

Voltage Output and Measurement.....................................................................................5
Current Output and Measurement.....................................................................................7
Load Regulation................................................................................................................9
Remote Sense..................................................................................................................12

Adjustment.............................................................................................................................. 13

Reverification..........................................................................................................................17
Worldwide Support and Services............................................................................................ 17

Required Software

Calibrating the NI 4113 requires you to install the following software on the calibration
system:
•

NI-DCPower 15.1 or later.

•

Supported application development environment (ADE)—LabVIEW or
LabWindows

™

/CVI

™

•

Supported operating system—Windows.

Содержание NI 4112



















Результаты поиска

Содержание NI 4112

Отзывы:

Похожие инструкции для NI 4112

Бренды по названию

Популярные бренды

National Instruments NI 4112, Процедура калибровки

Результаты поиска

Содержание NI 4112

Отзывы:

Похожие инструкции для NI 4112

Бренды по названию

Популярные бренды