National Instruments Network Adapter NI PXIe-1075 Скачать руководство пользователя | Manualshive

Страница: 38 / 78

background image

©

National Instruments Corporation

3-1

NI PXIe-1075 User Manual

3

Maintenance

This chapter describes basic maintenance procedures you can perform on
the NI PXIe-1075 chassis.

Caution

Disconnect the power cable prior to servicing a NI PXIe-1075 chassis.

Service Interval

Clean the chassis fan filters at a maximum interval of six months.
Depending on the amount of use and ambient dust levels in the operating
environment, the filters may require more frequent cleaning.

Clean dust from the chassis exterior (and interior) as needed, based on the
operating environment. Periodic cleaning increases reliability and cooling
performance.

Preparation

The information in this section is designed for use by qualified service
personnel. Read the

Read Me First: Safety and Radio-Frequency

Interference

document included with your kit before attempting any

procedures in this chapter.

Caution

Many components within the chassis are susceptible to static discharge damage.

Service the chassis only in a static-free environment. Observe standard handling
precautions for static-sensitive devices while servicing the chassis. Always wear a
grounded wrist strap or equivalent while servicing the chassis.

Cleaning

Cleaning procedures consist of exterior and interior cleaning of the chassis
and cleaning the fan filters. Refer to your module user documentation for
information on cleaning the individual CompactPCI or PXI Express
modules.

«
...
36
37
38
39
40
...
»

Содержание Network Adapter NI PXIe-1075















































































Отзывы:

Нет отзывов

Похожие инструкции для Network Adapter NI PXIe-1075

Бренд: Jabra Страницы: 15

Бренд: Paradyne Страницы: 85

Бренд: Phytec Страницы: 53

Бренд: ZyXEL Communications Страницы: 2

Бренд: Dahua Страницы: 24

SteelCentral NetExpress

Бренд: Riverbed Страницы: 38

Digital Encoder Plus

Бренд: IDT Страницы: 98

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

Бренд: XtendLan Страницы: 52

Бренд: SeaLevel Страницы: 21

Бренд: Renesas Страницы: 76

Бренд: Compal Страницы: 47

Бренд: Supero Страницы: 53

Бренд: Keil Страницы: 68

Бренд: ADS Technologies Страницы: 1

Бренд: CSL Страницы: 24

Бренд: McIntosh Страницы: 44

Бренд: ADTRAN Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды