National Instruments GPIB-VXI/C Скачать руководство пользователя

Страница: 85 / 226

Chapter 3

Local Command Set

National Instruments Corporation

3-43

GPIB-VXI/C User Manual

GPIB Address Configuration Commands and Queries

These GPIB address configuration commands are described in the following sections:

•

LaSaddr

•

LaSaddr?

•

Primary?

•

SaddrLa?

•

Saddrs?

•

SaDisCon

These commands and queries configure and report the relationships between VXI logical
addresses and GPIB addresses.

You can determine the GPIB-VXI/C’s primary address when used for multiple GPIB
secondary addressing by using the

Primary?

query from the serial port. You can determine

the relationships between GPIB addresses and VXI logical addresses by using the

Saddrs?

query followed by

SaddrLa?

queries, or by using the RM information query

Laddrs?

followed by

LaSaddr?

queries.

You can assign GPIB address links to Message-Based Servants of the GPIB-VXI/C with the

LaSaddr

command. The

SaDisCon

command deletes all GPIB address links except the link

to the GPIB-VXI/C local commands.

Note

The letters SA or SADDR in this chapter originally stood for GPIB Secondary

Address. The GPIB-VXI/C can be configured to handle multiple primary addresses
as well. The terminology has been left the same to maintain backward compatibility.

Содержание GPIB-VXI/C



































































































































































































































Результаты поиска

Содержание GPIB-VXI/C

Отзывы:

Похожие инструкции для GPIB-VXI/C

Бренды по названию

Популярные бренды

National Instruments GPIB-VXI/C, Руководство пользователя

Результаты поиска

Содержание GPIB-VXI/C

Отзывы:

Похожие инструкции для GPIB-VXI/C

Бренды по названию

Популярные бренды