National Instruments Deterministic Ethernet Expansion Chassis NI... Скачать руководство пользователя

Страница: 17 / 65

National Instruments Corporation

NI 9144 User Guide and Specifications

Figure 11.

Ethernet Connector Pinout

Safety Standards

This product meets the requirements of the following standards of safety
for electrical equipment for measurement, control, and laboratory use:

•

IEC 61010-1, EN 61010-1

•

UL 61010-1, CSA 61010-1

Note

For UL and other safety certifications, refer to the product label or the

Online

Product Certification

section.

Electromagnetic Compatibility

This product meets the requirements of the following EMC standards for
electrical equipment for measurement, control, and laboratory use:

•

EN 61326 (IEC 61326): Class A emissions; Basic immunity

•

EN 55011 (CISPR 11): Group 1, Class A emissions

•

AS/NZS CISPR 11: Group 1, Class A emissions

•

FCC 47 CFR Part 15B: Class A emissions

•

ICES-001: Class A emissions

Note

For the standards applied to assess the EMC performance of this product, refer to the

Online Product Certification

section.

Connector 1

Connector 2

Pin 1

Pin 8

Содержание Deterministic Ethernet Expansion Chassis NI...


































































Результаты поиска

Содержание Deterministic Ethernet Expansion Chassis NI...

Отзывы:

Похожие инструкции для Deterministic Ethernet Expansion Chassis NI...

Бренды по названию

Популярные бренды

National Instruments Deterministic Ethernet Expansion Chassis NI..., Руководство пользователя

Результаты поиска

Содержание Deterministic Ethernet Expansion Chassis NI...

Отзывы:

Похожие инструкции для Deterministic Ethernet Expansion Chassis NI...

Бренды по названию

Популярные бренды