National Instruments Deterministic Ethernet Expansion Chassis NI... Скачать руководство пользователя | Manualshive

Страница: 15 / 65

background image

©

National Instruments Corporation

15

NI 9144 User Guide and Specifications

Measurement Category I is for measurements performed on circuits not
directly connected to the electrical distribution system referred to as
MAINS voltage. MAINS is a hazardous live electrical supply system that
powers equipment. This category is for measurements of voltages from
specially protected secondary circuits. Such voltage measurements include
signal levels, special equipment, limited-energy parts of equipment,
circuits powered by regulated low-voltage sources, and electronics.

Caution

Do not connect the system to signals or use for measurements within

Measurement Categories II, III, or IV.

Hazardous Locations

U.S. (UL)................................................ Class I, Division 2, Groups A,

B, C, D, T4; Class I, Zone 2,
AEx nA IIC T4

Canada (C-UL)....................................... Class I, Division 2, Groups A,

B, C, D, T4; Class I, Zone 2,
Ex nA IIC T4

Europe (DEMKO).................................. Ex nA IIC T4

Environmental

The NI 9144 chassis is intended for indoor use only, but it may be used
outdoors if mounted in a suitably rated enclosure.

Operating temperature
(IEC 60068-2-1, IEC 60068-2-2)........... –40 to 70 °C

Note

To meet this operating temperature range, follow the guidelines in the installation

instructions for your EtherCAT system.

Storage temperature
(IEC 60068-2-1, IEC 60068-2-2)........... –40 to 85 °C

Ingress protection ................................... IP 40

Operating humidity
(IEC 60068-2-56) ................................... 10 to 90% RH, noncondensing

Storage humidity
(IEC 60068-2-56) ................................... 5 to 95% RH, noncondensing

Maximum altitude .................................. 2,000 m

Pollution Degree (IEC 60664) ............... 2

«
...
13
14
15
16
17
...
»

Содержание Deterministic Ethernet Expansion Chassis NI...


































































Отзывы:

Нет отзывов

Похожие инструкции для Deterministic Ethernet Expansion Chassis NI...

Бренд: Barracuda Networks Страницы: 2

Бренд: XDS Страницы: 99

Бренд: Lauterbach Страницы: 61

Бренд: Campbell Страницы: 42

Бренд: LAWO Страницы: 154

Бренд: Paradyne Страницы: 112

HiGain HLU-231 List 8F

Бренд: ADC Страницы: 7

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: FONESTAR Страницы: 8

Duinotech Lilypad Plus XC3920

Бренд: Jaycar Electronics Страницы: 2

Бренд: Digi Страницы: 116

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

UST510-52B-FL Series

Бренд: AXIOMTEK Страницы: 77

Бренд: c Страницы: 32

Бренд: RadiSys Страницы: 6

Бренд: Linksys Страницы: 37

BD7682FJ-EVK-301

Бренд: Rohm Страницы: 6

Бренд: Advantage Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды